L44640-L44610 bearing: complete specifications & equivalents
The L44640-L44610 is a ANSI ABMA 19.2 radial bearing sized 23.812 x 50.292 x 14.224 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 23.812 mm |
| Outer diameter D | 50.292 mm |
| Width B | 14.224 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 32 kN |
| Basic static load rating C0 | 34 kN |
| Limiting speed (mechanical) | 7400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 133 g |
| Manufacturer designation | NTN 4T-L44640/L44610 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 0.937 in |
|---|---|
| Outer diameter D | 1.98 in |
| Width B | 0.56 in |
| ISO bore code | 40 |
| Radial section height (D−d)/2 | 13.2 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 15 of 148 |
| Bore above smallest 4t-inch-series size | 11.112000000000002 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| L44640 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the L44640-L44610 model number is decoded
The NTN 2203E inch table prints 4T-L44640/L44610 at 23.812 mm bore (0.937 in), 50.292 mm cup OD and 14.224 mm assembled T, with a grease limiting speed of 7,400 r/min and an oil ceiling of 9,900 r/min. Unlike ISO 355 metric numbers, this ABMA code does not encode the bore arithmetically: L44640 identifies the cone of 23.812 mm (0.937 in) bore by catalogue lookup, and L44610 fixes the 50.292 mm OD. Catalogue mass of the 4T-L44640/L44610 cone-plus-cup set is 133 g; shaft and housing shoulders must carry that mass square to the axis during fitting. Cup-side note for L44610: within the light L family tables the L44640 cone is listed against several cup options, and it is the cup that fixes the 50.292 mm OD and the 14.224 mm assembled width — quote the full L44640/L44610 pair, never the cone alone. Minimum load matters at speed: an unloaded 4T-L44640/L44610 run near 7,400 r/min lets the rollers skid; lightly spring-preload high-speed pair arrangements.
Typical equipment & failure modes
Common applications
- small machine-tool feed and spindle counter-supports
- light trailer and boat-trailer wheel hubs
- small agricultural implement wheels and auger drives
- lawn, garden and powersport axle positions
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- brinell marks on cone and cup raceways from impact during handling or hammer fitting
Selection pitfalls — read before you substitute
- At 23.812 mm (0.937 in) bore the thin cone and cup distort under an over-tight shaft nut; set the 4T-L44640/L44610 pair with a dial indicator on end play rather than by locknut feel.
- The light L family at 23.812 mm bore (50.292×14.224 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full L44640/L44610 reference at purchase.
- ABMA makes the 23.812×50.292 mm envelope interchangeable, not the ratings: NTN prints 32/34 kN for this execution and another make of the same number can differ in roller complement.
- An unloaded 4T-L44640/L44610 near 7,400 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- Do not confuse T (14.224 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- The 32/34 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-L44640/L44610; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-L44640/L44610?
4T-L44640/L44610 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 23.812 mm bore (0.937 in), 50.292 mm outside diameter and 14.224 mm assembled width T (1.98 × 0.56 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 32 kN, C0 34 kN, grease limiting speed 7,400 r/min, oil speed 9,900 r/min, mass about 133 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-L44640/L44610 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the L44640 cone or the L44610 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 32/34 kN ratings change with the cup.
What is the difference between 4T-L44640/L44610 and a metric ISO 355 tapered bearing?
4T-L44640/L44610 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 23.812×50.292×14.224 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-L44640/L44610 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare L44640/L44610 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-L44640/L44610 list two speeds, 7,400 and 9,900 r/min?
The lower figure, 7,400 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-L44640/L44610 at 9,900 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.