32226T142-DB bearing: complete specifications & equivalents
The 32226T142-DB is a ISO 355 radial bearing sized 130 x 230 x 142 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 130 mm |
| Outer diameter D | 230 mm |
| Width B | 142 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1012 kN |
| Basic static load rating C0 | 1660 kN |
| Fatigue load limit Pu | 170 kN |
| Reference speed (thermal) | 1600 rpm |
| Limiting speed (mechanical) | 2800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 23000 g |
| Manufacturer designation | SKF 32226T142/DB |
| Standard | ISO 355 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants |
| Last verified | 2026-09-29 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & matched-db-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 9.055 in |
| Width B | 5.591 in |
| ISO bore code | 42 |
| Radial section height (D−d)/2 | 50 mm |
| Smallest bore in matched-db-series | 35 mm |
| Largest outer diameter in matched-db-series | 480 mm |
| Width range across matched-db-series | 41.5–288 mm |
| Bore position in matched-db-series (smallest first) | 18 of 30 |
| Bore above smallest matched-db-series size | 95 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 32226T142 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 32226T142-DB model number is decoded
SKF 32226T142/DB belongs to the SKF matched tapered-roller range — the 130 mm bore entry in back-to-back (O) matched pair arrangement, dimensioned 230 mm OD and 142 mm overall width for the pair.The code breaks down as base bearing 32226T142 plus matched-set suffix /DB: two bearings of the 130 mm bore size, paired back-to-back (O) matched pair, with the 142 mm overall width spanning the whole arrangement. In the back-to-back (O) arrangement the load lines diverge toward the shaft axis, giving the pair a wide effective spread: 32226T142-DB resists overturning moments and tilting loads stiffly, which is why O-sets are preferred for gearbox output shafts and pinion supports. Catalogue mass 23000 g covers both bearings and the ground spacer of 32226T142-DB; keep the set complete — substituting one bearing or a non-ground spacer destroys the factory clearance. Material and manufacturing detail: the 23000 g catalogue mass reflects through-hardened bearing steel machined to the listed envelope; ring roundness and width tolerance keep the mounted-setting scatter inside the catalogue class. When a matched /DB set like 32226T142-DB is replaced, replace the whole set: mixing a new bearing with a worn partner from the old set leaves the clearance and load sharing of the pair undefined. Clamp the assembled pair axially through the cones — never through the rollers — and verify the 142 mm overall width against the catalogue value before final torquing of the shaft nut.
Typical equipment & failure modes
Common applications
- large industrial mixer shafts
- offshore winch and drawworks drums
- rolling-mill roll-neck bearings
- large industrial mixer shafts
Known failure patterns
- axial overload spalling at the roller-rib contact beyond the single-row thrust rating
- uneven load sharing in a pair when spacer faces are not parallel to the bore
- pressed-steel cage wear or fracture after prolonged running above the limiting speed
- edge loading from shaft deflection or housing misalignment
- mounting score marks when the cone is cocked over the shaft keyway or a burr
Selection pitfalls — read before you substitute
- O and X arrangements are not interchangeable by turning the set around: 32226T142-DB in back-to-back (O) matched pair arrangement has its load-line geometry fixed — specify the arrangement from the shaft thermal and stiffness analysis.
- Clamp the 32226T142-DB pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
- Clamp the 32226T142-DB pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
- The 1012/1660 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
- Quote the full SKF 32226T142/DB designation when purchasing — base-number-only orders are ambiguous across executions and variants.
Frequently asked questions
What are the dimensions and catalogue data of 32226T142-DB?
The SKF 32226T142/DB is a matched pair of single-row tapered roller bearings in back-to-back (O) matched pair arrangement with 130 mm bore, 230 mm outer diameter and 142 mm overall width (5.118 × 9.055 × 5.591 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 1012 kN, C0 1660 kN, fatigue load limit Pu 170 kN, reference speed 1,600 r/min, limiting speed 2,800 r/min, mass about 23.00 kg.
What does the /DB suffix on 32226T142-DB mean?
The base 32226T142 is the ISO 355 single-row bearing; the /DB suffix marks the matched-set execution — the arrangement (back-to-back (O)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.
Are the C and C0 ratings of 32226T142-DB for one bearing or the pair?
They are for the complete matched pair: C 1012 kN dynamic and C0 1660 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 32226T142 table values.
Can 32226T142-DB be adjusted like two loose tapered bearings?
No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (m6 on a rotating 130 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.
When should a back-to-back (O) matched set be chosen?
Choose the back-to-back (O) set where moment stiffness dominates — pinion supports, gearbox output shafts, crane sheaves. The diverging load lines give the widest effective spread at the 130 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.