32936T103-DB bearing: complete specifications & equivalents
The 32936T103-DB is a ISO 355 radial bearing sized 180 x 250 x 103 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 180 mm |
| Outer diameter D | 250 mm |
| Width B | 103 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 746 kN |
| Basic static load rating C0 | 1460 kN |
| Fatigue load limit Pu | 137 kN |
| Reference speed (thermal) | 1500 rpm |
| Limiting speed (mechanical) | 2200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 14500 g |
| Manufacturer designation | SKF 32936T103/DB |
| Standard | ISO 355 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants |
| Last verified | 2026-09-29 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & matched-db-series range
| Bore d | 7.087 in |
|---|---|
| Outer diameter D | 9.843 in |
| Width B | 4.055 in |
| ISO bore code | 03 |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in matched-db-series | 35 mm |
| Largest outer diameter in matched-db-series | 480 mm |
| Width range across matched-db-series | 41.5–288 mm |
| Bore position in matched-db-series (smallest first) | 23 of 30 |
| Bore above smallest matched-db-series size | 145 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 32936T103 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 32936T103-DB model number is decoded
Back-to-back matching puts the large rib ends outward — the stiffest arrangement for moment load, but one that converts shaft thermal growth into preload change; the factory setting of 32936T103-DB already accounts for the expected temperature gradient across the 103 mm pair width. Selection arithmetic: the catalogue C 746 kN and C0 1460 kN are ratings of the complete pair, not of one bearing — never halve them back to a single-row figure when checking L10 life, and use the pair Pu 137 kN as the fatigue floor. Load system: C 746 kN against C0 1460 kN gives a 1.96 balance, and 4.14 kN of dynamic capacity per millimetre of the 180 mm bore is the density figure to compare against neighbouring sizes. Inspection shorthand: at overhaul, mark both bearings and the spacer of 32936T103-DB before disassembly — the set is a matched system, and re-assembling with one component reversed changes the factory setting. Lubrication for the pair should be sized against the combined 103 mm width and 14500 g mass: two roller sets sweep twice the contact area of a single bearing of the same bore.The SKF 32936T103/DB is a 180×250×103 mm matched tapered-roller set — two single-row bearings in back-to-back (O) matched pair arrangement, ground and shipped together with the axial clearance fixed at the factory.The code breaks down as base bearing 32936T103 plus matched-set suffix /DB: two bearings of the 180 mm bore size, paired back-to-back (O) matched pair, with the 103 mm overall width spanning the whole arrangement.
Typical equipment & failure modes
Common applications
- large crusher and mineral-processing drives
- wind-turbine main shafts
- marine propulsion gearboxes
- offshore winch and drawworks drums
Known failure patterns
- thermal preload runaway in an O-arrangement pair when inner-ring heat expands the setting
- roller large-end smearing against the cone rib after EP lubricant film failure
- pressed-steel cage wear or fracture after prolonged running above the limiting speed
- mounting score marks when the cone is cocked over the shaft keyway or a burr
- hard-particle indentation of the tapered raceway in unfiltered oil
Selection pitfalls — read before you substitute
- O and X arrangements are not interchangeable by turning the set around: 32936T103-DB in back-to-back (O) matched pair arrangement has its load-line geometry fixed — specify the arrangement from the shaft thermal and stiffness analysis.
- Spacer faces must stay parallel within the set's own tolerance; a tilted spacer in 32936T103-DB concentrates reversing thrust on one bearing and shows up as one-sided raceway wear.
- O and X arrangements are not interchangeable by turning the set around: 32936T103-DB in back-to-back (O) matched pair arrangement has its load-line geometry fixed — specify the arrangement from the shaft thermal and stiffness analysis.
- The 746/1460 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
- Quote the full SKF 32936T103/DB designation when purchasing — base-number-only orders are ambiguous across executions and variants.
Frequently asked questions
What are the dimensions and catalogue data of 32936T103-DB?
The SKF 32936T103/DB is a matched pair of single-row tapered roller bearings in back-to-back (O) matched pair arrangement with 180 mm bore, 250 mm outer diameter and 103 mm overall width (7.087 × 9.843 × 4.055 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 746 kN, C0 1460 kN, fatigue load limit Pu 137 kN, reference speed 1,500 r/min, limiting speed 2,200 r/min, mass about 14.50 kg.
What does the /DB suffix on 32936T103-DB mean?
The base 32936T103 is the ISO 355 single-row bearing; the /DB suffix marks the matched-set execution — the arrangement (back-to-back (O)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.
Are the C and C0 ratings of 32936T103-DB for one bearing or the pair?
They are for the complete matched pair: C 746 kN dynamic and C0 1460 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 32936T103 table values.
Can 32936T103-DB be adjusted like two loose tapered bearings?
No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (m6 on a rotating 180 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.
When should a back-to-back (O) matched set be chosen?
Choose the back-to-back (O) set where moment stiffness dominates — pinion supports, gearbox output shafts, crane sheaves. The diverging load lines give the widest effective spread at the 180 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.