30230-DF bearing: complete specifications & equivalents
The 30230-DF is a ISO 355 radial bearing sized 150 x 270 x 98 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 150 mm |
| Outer diameter D | 270 mm |
| Width B | 98 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 781 kN |
| Basic static load rating C0 | 1120 kN |
| Fatigue load limit Pu | 114 kN |
| Reference speed (thermal) | 1400 rpm |
| Limiting speed (mechanical) | 2400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 22000 g |
| Manufacturer designation | SKF 30230/DF |
| Standard | ISO 355 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants |
| Last verified | 2026-09-29 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & matched-df-series range
| Bore d | 5.906 in |
|---|---|
| Outer diameter D | 10.63 in |
| Width B | 3.858 in |
| ISO bore code | 30 |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in matched-df-series | 25 mm |
| Largest outer diameter in matched-df-series | 540 mm |
| Width range across matched-df-series | 34.5–280 mm |
| Bore position in matched-df-series (smallest first) | 22 of 35 |
| Bore above smallest matched-df-series size | 125 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 30230 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 30230-DF model number is decoded
Lubrication for the pair should be sized against the combined 98 mm width and 22000 g mass: two roller sets sweep twice the contact area of a single bearing of the same bore.The SKF 30230/DF is a 150×270×98 mm matched tapered-roller set — two single-row bearings in face-to-face (X) matched pair arrangement, ground and shipped together with the axial clearance fixed at the factory.Numbering ties the set to its envelope: base 30230 fixes the 150 mm bore and 270 mm OD of each bearing, the /DF suffix fixes the arrangement and setting, and the catalogue 98 mm width is the combined pair dimension. Face-to-face matching puts the small rib ends outward, so the pressure cones cross inside the pair; 30230-DF therefore runs cooler where the shaft expands axially, at the price of lower moment stiffness than an O-arrangement of the same 150 mm bore. Dividing the pair C 781 kN by the 150 mm bore gives 5.21 kN per millimetre of journal for the complete arrangement — a density metric that compares matched sets across the face-to-face (X) matched pair family. Assembly datum check: verify the 98 mm width against the drawing before clamping — the width is the assembled result and the quickest field check that the correct execution of 30230-DF is on the shaft. Load sharing in 30230-DF depends on spacer face parallelism; a cocked spacer concentrates the reversing thrust on one bearing of the pair and shows up as asymmetric raceway wear at overhaul.
Typical equipment & failure modes
Common applications
- heavy-duty rolling-mill gearboxes
- large crusher and mineral-processing drives
- wind-turbine main shafts
- offshore winch and drawworks drums
Known failure patterns
- thermal preload runaway in an O-arrangement pair when inner-ring heat expands the setting
- axial overload spalling at the roller-rib contact beyond the single-row thrust rating
- cage pocket scoring when the bearing starts cold with grease of too-high base-oil viscosity
- fretting corrosion on a loose rotating shaft seat
- fretting corrosion on a loose rotating shaft seat
Selection pitfalls — read before you substitute
- Spacer faces must stay parallel within the set's own tolerance; a tilted spacer in 30230-DF concentrates reversing thrust on one bearing and shows up as one-sided raceway wear.
- Clamp the 30230-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
- Spacer faces must stay parallel within the set's own tolerance; a tilted spacer in 30230-DF concentrates reversing thrust on one bearing and shows up as one-sided raceway wear.
- The 781/1120 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
- Quote the full SKF 30230/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.
Frequently asked questions
What are the dimensions and catalogue data of 30230-DF?
The SKF 30230/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 150 mm bore, 270 mm outer diameter and 98 mm overall width (5.906 × 10.63 × 3.858 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 781 kN, C0 1120 kN, fatigue load limit Pu 114 kN, reference speed 1,400 r/min, limiting speed 2,400 r/min, mass about 22.00 kg.
What does the /DF suffix on 30230-DF mean?
The base 30230 is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.
Are the C and C0 ratings of 30230-DF for one bearing or the pair?
They are for the complete matched pair: C 781 kN dynamic and C0 1120 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 30230 table values.
Can 30230-DF be adjusted like two loose tapered bearings?
No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (m6 on a rotating 150 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.
When should a face-to-face (X) matched set be chosen?
Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 150 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.