30312-DF bearing: complete specifications & equivalents
The 30312-DF is a ISO 355 radial bearing sized 60 x 130 x 67 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 60 mm |
| Outer diameter D | 130 mm |
| Width B | 67 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 357 kN |
| Basic static load rating C0 | 390 kN |
| Fatigue load limit Pu | 47.5 kN |
| Reference speed (thermal) | 3600 rpm |
| Limiting speed (mechanical) | 5300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 4100 g |
| Manufacturer designation | SKF 30312/DF |
| Standard | ISO 355 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants |
| Last verified | 2026-09-29 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & matched-df-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 5.118 in |
| Width B | 2.638 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in matched-df-series | 25 mm |
| Largest outer diameter in matched-df-series | 540 mm |
| Width range across matched-df-series | 34.5–280 mm |
| Bore position in matched-df-series (smallest first) | 8 of 35 |
| Bore above smallest matched-df-series size | 35 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 30312 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 30312-DF model number is decoded
Catalogue mass 4100 g covers both bearings and the ground spacer of 30312-DF; keep the set complete — substituting one bearing or a non-ground spacer destroys the factory clearance. Operating context for the 60 mm bore: a shaft of this diameter typically runs in the large-bore band of industrial duty, and the 130 mm OD places the housing shoulder near 138 mm outer abutment. Load sharing in 30312-DF depends on spacer face parallelism; a cocked spacer concentrates the reversing thrust on one bearing of the pair and shows up as asymmetric raceway wear at overhaul. The rotating cones of 30312-DF take a k5 seat on the 60 mm shaft; the cups are a transition-to-loose fit so the pair can be clamped to its factory setting during assembly.For a 60 mm shaft carrying reversing axial load, SKF lists 30312-DF under catalogue execution SKF 30312/DF: a factory-matched face-to-face (X) matched pair tapered-roller pair, set and measured as one unit.Reading the designation: 30312 is the ISO 355 single-row base bearing (60 mm bore), and the suffix /DF marks the matched-set execution — arrangement, spacer grinding and factory clearance class. The pair envelope is 60×130×67 mm; the width covers both bearings of the set. Face-to-face matching puts the small rib ends outward, so the pressure cones cross inside the pair; 30312-DF therefore runs cooler where the shaft expands axially, at the price of lower moment stiffness than an O-arrangement of the same 60 mm bore.
Typical equipment & failure modes
Common applications
- large process pump and compressor shafts
- rolling-mill auxiliary drives
- crane sheave and hoist gearboxes
- heavy industrial gearboxes and speed reducers
Known failure patterns
- roller large-end smearing against the cone rib after EP lubricant film failure
- thermal preload runaway in an O-arrangement pair when inner-ring heat expands the setting
- cage pocket scoring when the bearing starts cold with grease of too-high base-oil viscosity
- hard-particle indentation of the tapered raceway in unfiltered oil
- fretting corrosion on a loose rotating shaft seat
Selection pitfalls — read before you substitute
- Clamp the 30312-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
- Clamp the 30312-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
- A matched /DF set is ground as one system: never separate the two bearings of 30312-DF or swap the spacer — the factory clearance is lost the moment the set is broken.
- The 357/390 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
- Quote the full SKF 30312/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.
Frequently asked questions
What are the dimensions and catalogue data of 30312-DF?
The SKF 30312/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 60 mm bore, 130 mm outer diameter and 67 mm overall width (2.362 × 5.118 × 2.638 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 357 kN, C0 390 kN, fatigue load limit Pu 47.5 kN, reference speed 3,600 r/min, limiting speed 5,300 r/min, mass about 4.10 kg.
What does the /DF suffix on 30312-DF mean?
The base 30312 is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.
Are the C and C0 ratings of 30312-DF for one bearing or the pair?
They are for the complete matched pair: C 357 kN dynamic and C0 390 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 30312 table values.
Can 30312-DF be adjusted like two loose tapered bearings?
No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (k5 on a rotating 60 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.
When should a face-to-face (X) matched set be chosen?
Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 60 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.