32056X-DF bearing: complete specifications & equivalents
The 32056X-DF is a ISO 355 radial bearing sized 280 x 420 x 174 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 280 mm |
| Outer diameter D | 420 mm |
| Width B | 174 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 2208 kN |
| Basic static load rating C0 | 4750 kN |
| Fatigue load limit Pu | 400 kN |
| Reference speed (thermal) | 800 rpm |
| Limiting speed (mechanical) | 1300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 84000 g |
| Manufacturer designation | SKF 32056 X/DF |
| Standard | ISO 355 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants |
| Last verified | 2026-09-29 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & matched-df-series range
| Bore d | 11.024 in |
|---|---|
| Outer diameter D | 16.535 in |
| Width B | 6.85 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 70 mm |
| Smallest bore in matched-df-series | 25 mm |
| Largest outer diameter in matched-df-series | 540 mm |
| Width range across matched-df-series | 34.5–280 mm |
| Bore position in matched-df-series (smallest first) | 31 of 35 |
| Bore above smallest matched-df-series size | 255 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 32056X | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 32056X-DF model number is decoded
Lubrication for the pair should be sized against the combined 174 mm width and 84000 g mass: two roller sets sweep twice the contact area of a single bearing of the same bore.Ordering number SKF 32056 X/DF in SKF catalogue PUB BU/P1 17000 denotes two single-row tapered roller bearings supplied as a matched face-to-face (X) matched pair set for a 280 mm shaft — one order number, one factory setting.Reading the designation: 32056 X is the ISO 355 single-row base bearing (280 mm bore), and the suffix /DF marks the matched-set execution — arrangement, spacer grinding and factory clearance class. The pair envelope is 280×420×174 mm; the width covers both bearings of the set. In the face-to-face (X) arrangement the load lines of the two bearings converge toward the shaft axis: the set tolerates shaft deflection and thermal growth better than a back-to-back pair, but is less stiff against overturning moments. The 174 mm overall width of 32056X-DF is the axial space the pair occupies. Speed planning for the set uses the catalogue pair values: 800 r/min thermal reference and 1,300 r/min mechanical limiting speed — a matched pair runs warmer than one bearing because two roller sets share the 174 mm space. Assembly datum check: verify the 174 mm width against the drawing before clamping — the width is the assembled result and the quickest field check that the correct execution of 32056X-DF is on the shaft. When a matched /DF set like 32056X-DF is replaced, replace the whole set: mixing a new bearing with a worn partner from the old set leaves the clearance and load sharing of the pair undefined.
Typical equipment & failure modes
Common applications
- heavy-duty rolling-mill gearboxes
- large crusher and mineral-processing drives
- wind-turbine main shafts
- offshore winch and drawworks drums
Known failure patterns
- thermal preload runaway in an O-arrangement pair when inner-ring heat expands the setting
- preload loss as the mounted pair relaxes, letting rollers skid and smear the raceways
- cage pocket scoring when the bearing starts cold with grease of too-high base-oil viscosity
- grease degradation after long shelf storage without rotation or re-greasing
- grease degradation after long shelf storage without rotation or re-greasing
Selection pitfalls — read before you substitute
- Spacer faces must stay parallel within the set's own tolerance; a tilted spacer in 32056X-DF concentrates reversing thrust on one bearing and shows up as one-sided raceway wear.
- Clamp the 32056X-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
- O and X arrangements are not interchangeable by turning the set around: 32056X-DF in face-to-face (X) matched pair arrangement has its load-line geometry fixed — specify the arrangement from the shaft thermal and stiffness analysis.
- The 2208/4750 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
- Quote the full SKF 32056 X/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.
Frequently asked questions
What are the dimensions and catalogue data of 32056X-DF?
The SKF 32056 X/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 280 mm bore, 420 mm outer diameter and 174 mm overall width (11.024 × 16.535 × 6.85 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 2208 kN, C0 4750 kN, fatigue load limit Pu 400 kN, reference speed 800 r/min, limiting speed 1,300 r/min, mass about 84.00 kg.
What does the /DF suffix on 32056X-DF mean?
The base 32056 X is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.
Are the C and C0 ratings of 32056X-DF for one bearing or the pair?
They are for the complete matched pair: C 2208 kN dynamic and C0 4750 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 32056 X table values.
Can 32056X-DF be adjusted like two loose tapered bearings?
No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (m6 on a rotating 280 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.
When should a face-to-face (X) matched set be chosen?
Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 280 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.