32212-DF bearing: complete specifications & equivalents

The 32212-DF is a ISO 355 radial bearing sized 60 x 110 x 59.5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 110 mm d = 60 B = 59.5 mm side section front view
Principal dimensions: bore d 60 mm, outer diameter D 110 mm, width B 59.5 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 60 mm
Outer diameter D 110 mm
Width B 59.5 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 266 kN
Basic static load rating C0 320 kN
Fatigue load limit Pu 37.5 kN
Reference speed (thermal) 4000 rpm
Limiting speed (mechanical) 6000 rpm
Operating temperature -40 to +120 °C
Mass 2400 g
Manufacturer designation SKF 32212/DF
Standard ISO 355
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants
Last verified 2026-09-29

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & matched-df-series range

Bore d2.362 in
Outer diameter D4.331 in
Width B2.343 in
ISO bore code12
Radial section height (D−d)/225 mm
Smallest bore in matched-df-series25 mm
Largest outer diameter in matched-df-series540 mm
Width range across matched-df-series34.5–280 mm
Bore position in matched-df-series (smallest first)8 of 35
Bore above smallest matched-df-series size35 mm

Mounting, setting & life for 32212-DF

Fits & mounting

  • Tapered bearings are separable: press the cup square into the housing and fit the cone on the shaft — usually an interference fit on both seats in wheel/hub positions.
  • Mount the cone by induction heating (max 120 °C); never strike the cage or rollers directly.
  • Shaft and housing shoulders must clear the ring chamfers so the cone and cup seat fully against their faces.

Setting — the step deep-groove bearings never need

  • After seating, set the assembly to a defined end play or preload with the locknut/shim arrangement; locknut torque seats the parts — it is not the final adjustment.
  • General free-running positions: back the nut off while measuring with a dial indicator to a small end play (commonly around 0.05–0.15 mm for medium metric hubs — follow the OEM value).
  • Pinions and stiff arrangements run a controlled preload; too much preload is the classic cause of early spalling and heat.
  • Sealed factory-set units exist for specific designations — the open 32212-DF assumes the application sets and lubricates it.

Lubrication

Open TRBs are lubricated by the application. Fill the bearing with grease (typically around one third to one half of the free cavity — overpacking a TRB causes churning heat) and provide a relubrication path; intervals depend on contamination and temperature, not on catalogue rating alone.

Why the equivalent load matters more here

TRBs carry combined radial and axial loads, so the dynamic equivalent load P is computed with the bearing's e, X and Y factors for the actual thrust ratio — using the radial load alone over-estimates life badly.

Worked L10 life example (illustrative duty)

For roller bearings the life exponent is p = 10/3: L10h = (C/P)10/3 · 106 / (60·n). Taking an example equivalent load P = 53.2 kN (20% of C) at n = 1,500 r/min — substitute the real P from the X/Y calculation:

C = 266.0 kN → L10h ≈ 2,375 hours

Choosing a series at the same 60 mm bore

SeriesOpen executionOD × width TC (kN)C0 (kN)Limiting speed (r/min)
320xx3201295 × 2397.0124.08,800
302xx30212110 × 23.75120.0114.06,000
322xx32212110 × 29.75158.0171.08,000
332xx33212U110 × 38179.0223.03,400
303xx30312D130 × 33.5167.0176.02,700
323xx32312C130 × 48.5237.0296.02,900
313xx31312130 × 33.5177.0166.05,300

Different series at the same bore are not drop-in swaps — OD, width and contact angle all change — and a cone number alone never identifies a complete set. Verify matches per the cross-reference levels guide; envelope variants are on the 60×110×59.5 envelope page.

Cross references & equivalents

Equivalent modelBrandMatch levelNote
32212 FAG verify
Commonly quoted cross reference; confirm against the target catalog before ordering.
Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 32212-DF model number is decoded

In the face-to-face (X) arrangement the load lines of the two bearings converge toward the shaft axis: the set tolerates shaft deflection and thermal growth better than a back-to-back pair, but is less stiff against overturning moments. The 59.5 mm overall width of 32212-DF is the axial space the pair occupies. Speed planning for the set uses the catalogue pair values: 4,000 r/min thermal reference and 6,000 r/min mechanical limiting speed — a matched pair runs warmer than one bearing because two roller sets share the 59.5 mm space. Material and manufacturing detail: the 2400 g catalogue mass reflects through-hardened bearing steel machined to the listed envelope; ring roundness and width tolerance keep the mounted-setting scatter inside the catalogue class. Load sharing in 32212-DF depends on spacer face parallelism; a cocked spacer concentrates the reversing thrust on one bearing of the pair and shows up as asymmetric raceway wear at overhaul. Lubrication for the pair should be sized against the combined 59.5 mm width and 2400 g mass: two roller sets sweep twice the contact area of a single bearing of the same bore.32212-DF is a matched pair of single-row tapered roller bearings arranged face-to-face (X) matched pair, supplied by SKF in SKF catalogue PUB BU/P1 17000 as one factory-set unit: the two bearings, spacers and setting are matched together and must not be mixed with other sets.Reading the designation: 32212 is the ISO 355 single-row base bearing (60 mm bore), and the suffix /DF marks the matched-set execution — arrangement, spacer grinding and factory clearance class. The pair envelope is 60×110×59.5 mm; the width covers both bearings of the set.

Typical equipment & failure modes

Common applications

  • paper-machine and printing rolls
  • construction machinery drives
  • marine deck machinery shafts
  • large process pump and compressor shafts

Known failure patterns

  • false brinelling on idle paired sets exposed to machine vibration
  • thermal preload runaway in an O-arrangement pair when inner-ring heat expands the setting
  • pressed-steel cage wear or fracture after prolonged running above the limiting speed
  • mounting score marks when the cone is cocked over the shaft keyway or a burr
  • mounting score marks when the cone is cocked over the shaft keyway or a burr

Selection pitfalls — read before you substitute

  • A matched /DF set is ground as one system: never separate the two bearings of 32212-DF or swap the spacer — the factory clearance is lost the moment the set is broken.
  • Setting is built into 32212-DF; the classic field error is re-adjusting a matched pair as if it were two loose single bearings, which destroys the /DF clearance class.
  • O and X arrangements are not interchangeable by turning the set around: 32212-DF in face-to-face (X) matched pair arrangement has its load-line geometry fixed — specify the arrangement from the shaft thermal and stiffness analysis.
  • The 266/320 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
  • Quote the full SKF 32212/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.

Frequently asked questions

What are the dimensions and catalogue data of 32212-DF?

The SKF 32212/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 60 mm bore, 110 mm outer diameter and 59.5 mm overall width (2.362 × 4.331 × 2.343 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 266 kN, C0 320 kN, fatigue load limit Pu 37.5 kN, reference speed 4,000 r/min, limiting speed 6,000 r/min, mass about 2.40 kg.

What does the /DF suffix on 32212-DF mean?

The base 32212 is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.

Are the C and C0 ratings of 32212-DF for one bearing or the pair?

They are for the complete matched pair: C 266 kN dynamic and C0 320 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 32212 table values.

Can 32212-DF be adjusted like two loose tapered bearings?

No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (k5 on a rotating 60 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.

When should a face-to-face (X) matched set be chosen?

Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 60 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.