10×26×8 mm bearings
16 models from 5 brands across 2 types share this ISO 15 envelope: 10 mm bore, 26 mm outside diameter, 8 mm width (0.394×1.024×0.315 in), 8 mm radial section.
16 models fit this space 5 brands 15 with catalogue C rating
Dimensional interchange — verify before substituting
These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.
| Model | Type | Brand | Seal | Clearance | C (kN) | C0 (kN) | Mass (g) |
|---|---|---|---|---|---|---|---|
| 6000 | Deep Groove Ball | SKF | open | CN | 4.75 | 1.96 | 19 |
| 6000-2RS | Deep Groove Ball | SKF | 2RS | CN | 4.75 | 1.96 | 19 |
| 6000-2RS-FAG | Deep Groove Ball | FAG | 2RS | CN | 5.3 | 1.97 | 18 |
| 6000-2RS-NSK | Deep Groove Ball | NSK | 2RS | CN | 5.05 | 1.97 | 18 |
| 6000-FAG | Deep Groove Ball | FAG | open | CN | 5.3 | 1.97 | 17 |
| 6000-NSK | Deep Groove Ball | NSK | open | CN | 5.05 | 1.97 | 18 |
| 6000-RSR | Deep Groove Ball | SKF | RSR | CN | 4.75 | 1.96 | 19 |
| 6000-RSR-NSK | Deep Groove Ball | NSK | RSR | CN | 5.05 | 1.97 | 18 |
| 6000-ZZ | Deep Groove Ball | SKF | ZZ | CN | 4.75 | 1.96 | 20 |
| 6000-ZZ-FAG | Deep Groove Ball | FAG | ZZ | CN | 5.3 | 1.97 | 19 |
| 6000-ZZ-NSK | Deep Groove Ball | NSK | ZZ | CN | 5.05 | 1.97 | 18 |
| 7000 | Angular Contact Ball | GENERIC-ISO | open | CN | — | — | 18 |
| 7000-NTN | Angular Contact Ball | NTN | open | CN | 5.1 | 2.07 | 23 |
| W6000 | Deep Groove Ball | SKF | open | CN | 3.97 | 1.96 | 17 |
| W6000-2RS | Deep Groove Ball | SKF | 2RS | CN | 3.97 | 1.96 | 18 |
| W6000-ZZ | Deep Groove Ball | SKF | ZZ | CN | 3.97 | 1.96 | 18 |
Substitution verification checklist
- Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
- Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
- Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
- Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
- Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.
Browse all 10 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6000, 6000-2RS, 6000-2RS-FAG, 6000-2RS-NSK, 6000-FAG, 6000-NSK, 6000-RSR, 6000-RSR-NSK, 6000-ZZ, 6000-ZZ-FAG, 6000-ZZ-NSK, 7000, 7000-NTN, W6000, W6000-2RS, W6000-ZZ.
Frequently asked questions
Are all 10×26×8 mm bearings interchangeable?
They share the same ISO 15 boundary dimensions — 10 mm bore, 26 mm OD, 8 mm width (0.394×1.024×0.315 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 16 models listed here and must be checked against the duty before substitution.
Is it a drop-in replacement if two bearings both measure 10×26×8?
Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.
What is 10×26×8 mm in inches?
10×26×8 mm converts to 0.394×1.024×0.315 in, with a 8 mm (0.315 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6000, 6000-2RS, 6000-2RS-FAG mount in the same space despite different internal designs.