160×240×60 mm bearings

12 models from 3 brands across 3 types share this ISO 15 envelope: 160 mm bore, 240 mm outside diameter, 60 mm width (6.299×9.449×2.362 in), 40 mm radial section.

12 models fit this space 3 brands 12 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23032 Spherical Roller SKF open CN 614 880 9700
23032-CCK-W33 Spherical Roller SKF open CN 614 880 14500
23032EAD1 Spherical Roller NTN open CN 748 1000 9320
23032EAKD1 Spherical Roller NTN open CN 748 1000 9030
23032EMD1 Spherical Roller NTN open CN 748 1000 9370
23032EMKD1 Spherical Roller NTN open CN 748 1000 9090
323032 Tapered Roller NTN open CN 475 765 9420
413032 Tapered Roller NTN open CN 370 535 8390
NCF3032-CV Cylindrical Roller SKF open CN 512 800 9100
NN3032 Cylindrical Roller NTN open CN 415 660 8920
NN3032K Cylindrical Roller NTN open CN 415 660 8590
SL183032 Cylindrical Roller FAG open CN 540 800 8800

Note: catalogue dynamic load ratings for this envelope span 370.0– 748.0 kN — a 102% spread between designs in the very same 160×240×60 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 160 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23032, 23032-CCK-W33, 23032EAD1, 23032EAKD1, 23032EMD1, 23032EMKD1, 323032, 413032, NCF3032-CV, NN3032, NN3032K, SL183032.

Frequently asked questions

Are all 160×240×60 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 160 mm bore, 240 mm OD, 60 mm width (6.299×9.449×2.362 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 12 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 160×240×60?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 160×240×60 mm in inches?

160×240×60 mm converts to 6.299×9.449×2.362 in, with a 40 mm (1.575 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23032, 23032-CCK-W33, 23032EAD1 mount in the same space despite different internal designs.