23032EMD1 bearing: complete specifications & equivalents
The 23032EMD1 is a ISO 15 radial bearing sized 160 x 240 x 60 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 160 mm |
| Outer diameter D | 240 mm |
| Width B | 60 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 748 kN |
| Basic static load rating C0 | 1000 kN |
| Fatigue load limit Pu | 59.1 kN |
| Limiting speed (mechanical) | 1800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 9370 g |
| Manufacturer designation | NTN 23032EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23000-series range
| Bore d | 6.299 in |
|---|---|
| Outer diameter D | 9.449 in |
| Width B | 2.362 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 1580 mm |
| Width range across 23000-series | 27–345 mm |
| Bore position in 23000-series (smallest first) | 13 of 46 |
| Bore above smallest 23000-series size | 90 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23032EMKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23032EMKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23032EMD1 model number is decoded
23032EMD1 is the EM machined-brass-cage execution of NTN's spherical roller range for a 160 mm shaft — 748 kN basic dynamic capacity in a 9370 g, open ISO 15 envelope. Reading the full code: the number gives the 160×240 mm envelope, EM names the cage/capacity execution, no bore suffix means cylindrical bore for a direct shaft seat, and D1 outer-ring annular oil groove with holes completes the order number. The sphered outer raceway lets the inner-ring assembly pivot, accommodating shaft deflection and housing misalignment (around 1–2° for this class; use the 2203E value for the exact series) without edge loading the rollers. Speed planning: 1,800 r/min grease limiting speed is the cage/kinematic ceiling and 2,300 r/min is the oil-lubricated value for the 160 mm bore; vibrating screens rarely approach either and are load/cage limited instead. Never mount 23032EMD1 by striking the outer ring through the roller set; drive through ring faces (or the adapter sleeve nut) and support the ring square to avoid brinelling the 240 mm race.
Typical equipment & failure modes
Common applications
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- cage damage when a mounting force is applied through the roller set instead of the ring face
- roller-end smearing during skidding starts under light load and high viscosity grease
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- rolling-contact fatigue after the catalogue L10 life at the actual load
Selection pitfalls — read before you substitute
- At 160 mm bore 23032EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Do not confuse EA and EM at the same number: 23032EMD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 160×240 mm envelope is identical.
- Do not confuse EA and EM at the same number: 23032EMD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 160×240 mm envelope is identical.
- Do not confuse EA and EM at the same number: 23032EMD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 160×240 mm envelope is identical.
- Minimum load must be maintained even at rest under vibration: an unloaded 23032EMD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- The 748/1000 kN ratings, 59.1 kN Pu and 9370 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23032EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23032EMD1?
23032EMD1 is an NTN double-row spherical roller bearing to ISO 15: 160 mm bore, 240 mm OD and 60 mm width (6.299 × 9.449 × 2.362 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 748 kN, C0 1000 kN, Pu 59.1 kN, grease limiting speed 1,800 r/min, oil 2,300 r/min, mass about 9370 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23032EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23032EMKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23032EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23032EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23032EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23032EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 748 kN C / 1000 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.