MPNbase

17×40×16 mm bearings

8 models from 2 brands across 3 types share this ISO 15 envelope: 17 mm bore, 40 mm outside diameter, 16 mm width (0.669×1.575×0.630 in), 11.5 mm radial section.

8 models fit this space 2 brands 8 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
2203 Self-Aligning Ball NTN open — 9.95 2.42 89
2203-E-2RS1TN9 Self-Aligning Ball SKF 2RS CN 8.84 2.2 89
2203-ETN9 Self-Aligning Ball SKF open CN 10.6 2.55 88
4203-ATN9 Deep Groove Ball SKF open CN 14.8 9.5 90
62203-2RS Deep Groove Ball SKF 2RS CN 9.56 4.75 89
NJ2203-ECP Cylindrical Roller SKF open CN 27.5 21.6 93
NU2203-ECP Cylindrical Roller SKF open CN 27.5 21.6 87
NUP2203-ECP Cylindrical Roller SKF open CN 27.5 21.6 97

Note: catalogue dynamic load ratings for this envelope span 8.8– 27.5 kN — a 211% spread between designs in the very same 17×40×16 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 17 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 2203, 2203-E-2RS1TN9, 2203-ETN9, 4203-ATN9, 62203-2RS, NJ2203-ECP, NU2203-ECP, NUP2203-ECP.

Frequently asked questions

Are all 17×40×16 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 17 mm bore, 40 mm OD, 16 mm width (0.669×1.575×0.630 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 8 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 17×40×16?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 17×40×16 mm in inches?

17×40×16 mm converts to 0.669×1.575×0.630 in, with a 11.5 mm (0.453 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 2203, 2203-E-2RS1TN9, 2203-ETN9 mount in the same space despite different internal designs.