4203-ATN9 bearing: complete specifications & equivalents
The 4203-ATN9 is a ISO 15 radial bearing sized 17 x 40 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 17 mm |
| Outer diameter D | 40 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 14.8 kN |
| Basic static load rating C0 | 9.5 kN |
| Fatigue load limit Pu | 0.405 kN |
| Reference speed (thermal) | 28000 rpm |
| Limiting speed (mechanical) | 15000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 90 g |
| Manufacturer designation | 4203 ATN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 4200-series range
| Bore d | 0.669 in |
|---|---|
| Outer diameter D | 1.575 in |
| Width B | 0.63 in |
| ISO bore code | 03 |
| Radial section height (D−d)/2 | 11.5 mm |
| Smallest bore in 4200-series | 10 mm |
| Largest outer diameter in 4200-series | 160 mm |
| Width range across 4200-series | 14–40 mm |
| Bore position in 4200-series (smallest first) | 4 of 19 |
| Bore above smallest 4200-series size | 7 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 62203-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 17×40×16 mm envelope as SKF 62203-2RS1, but catalogue C/C0 differ (14.8/9.5 kN vs 9.56/4.75 kN) — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 4203-ATN9 model number is decoded
4203 ATN9 is a double-row deep-groove ball bearing in the 4200-series: bore code 03 follows the 10/12/15/17 mm exception table, so 4203 fits a 17 mm shaft. Two complete ball sets share the 17×40×16 mm (0.669×1.575×0.63 in) envelope, giving C 14.8 kN, C0 9.5 kN and Pu 0.405 kN, with reversing axial capacity a single-row bearing cannot match. ATN9 is the glass-fibre PA66 cage. Limiting speed 15000 r/min, mass 90 g. The arrangement is open and requires external sealing.
Typical equipment & failure modes
Common applications
- double-supported pump impeller shafts
- gearbox layshafts with reversing axial load
- agricultural gearboxes
- belt take-up and tensioner units
Known failure patterns
- uneven load sharing between the two raceways when one ring is tilted
- polyamide cage embrittlement after sustained high-temperature service
- edge loading from shaft deflection or housing misalignment
- rolling-contact fatigue spalling once the catalogue L10 life is exceeded
Selection pitfalls — read before you substitute
- Double-row 4203 is open and needs application sealing and lubrication; in dusty drives add external seals rather than expecting the bearing itself to stay clean.
- C 14.8 kN in a 16 mm width is the strength of the double-row design; use it for combined or reversing axial loads rather than pure radial duty where a slimmer single-row bearing would run cooler.
- Fit both rings square on the shoulders: the narrow internal land between the two raceways of 4203-ATN9 is sensitive to cocking during pressing.
- The ATN9 cage is glass-fibre-reinforced polyamide 66: it is light and quiet but caps continuous service around 100–120 °C in oil/grease — above that use the pressed-steel or machined-cage version of the 17 mm position.
- C 14.8 kN in a 16 mm width is the strength of the double-row design; use it for combined or reversing axial loads rather than pure radial duty where a slimmer single-row bearing would run cooler.
- Do not preload 4203-ATN9 to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
Frequently asked questions
What are the dimensions of 4203-ATN9?
Double-row 4203 ATN9 measures 17×40×16 mm (0.669×1.575×0.63 in), about 90 g.
What does ATN9 mean on 4203 ATN9?
A = double-row deep-groove arrangement, TN9 is a glass-fibre-reinforced polyamide 66 cage; it limits continuous temperature to roughly 100–120 °C.
How is 4203-ATN9 lubricated and sealed?
The ATN9 execution is open and greased/oiled by the application; provide external lip seals and a regreasing path for dirty duty.
What load does 4203-ATN9 carry?
C 14.8 kN, C0 9.5 kN and Pu 0.405 kN per catalogue 17000; both rows share the load when the rings sit parallel.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.