MPNbase

180×280×46 mm bearings

14 models from 3 brands across 3 types share this ISO 15 envelope: 180 mm bore, 280 mm outside diameter, 46 mm width (7.087×11.024×1.811 in), 50 mm radial section.

14 models fit this space 3 brands 14 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6036 Deep Groove Ball SKF open CN 190 200 9100
6036-M Deep Groove Ball SKF open CN 190 200 10500
6036-NSK Deep Groove Ball NSK open CN 198 185 8880
6036-NTN Deep Groove Ball NTN open CN 210 199 8800
6036-RSR Deep Groove Ball NSK RSR CN 198 185 8880
6036-ZZ Deep Groove Ball NSK ZZ CN 198 185 8880
7036 Angular Contact Ball NTN open CN 242 266 10400
7036-BGM Angular Contact Ball SKF open CN 195 240 10000
N1036 Cylindrical Roller NTN open CN 380 485 10100
NJ1036 Cylindrical Roller NTN open CN 380 485 10100
NJ1036-ML Cylindrical Roller SKF open CN 336 475 10500
NU1036 Cylindrical Roller NTN open CN 380 485 10100
NU1036-ML Cylindrical Roller SKF open CN 336 475 10500
NUP1036 Cylindrical Roller NTN open CN 380 485 10100

Note: catalogue dynamic load ratings for this envelope span 190.0– 380.0 kN — a 100% spread between designs in the very same 180×280×46 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 180 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6036, 6036-M, 6036-NSK, 6036-NTN, 6036-RSR, 6036-ZZ, 7036, 7036-BGM, N1036, NJ1036, NJ1036-ML, NU1036, NU1036-ML, NUP1036.

Frequently asked questions

Are all 180×280×46 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 180 mm bore, 280 mm OD, 46 mm width (7.087×11.024×1.811 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 14 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 180×280×46?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 180×280×46 mm in inches?

180×280×46 mm converts to 7.087×11.024×1.811 in, with a 50 mm (1.969 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6036, 6036-M, 6036-NSK mount in the same space despite different internal designs.