300×460×118 mm bearings

12 models from 3 brands across 4 types share this ISO 15 envelope: 300 mm bore, 460 mm outside diameter, 118 mm width (11.811×18.110×4.646 in), 80 mm radial section.

12 models fit this space 3 brands 12 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23060 Spherical Roller SKF open CN 2219 3450 71500
23060-CCK-W33 Spherical Roller SKF open CN 2219 3450 90000
23060EMD1 Spherical Roller NTN open CN 2400 3610 72900
23060EMKD1 Spherical Roller NTN open CN 2400 3610 70900
323060UTG Tapered Roller NTN open CN 2070 3150 69200
413060UTG Tapered Roller NTN open CN 1370 1990 65600
C3060-KM CARB Toroidal Roller SKF open CN 2160 3750 72000
C3060-M CARB Toroidal Roller SKF open CN 2160 3750 72000
NCF3060-CV Cylindrical Roller SKF open CN 1900 3250 65500
NN3060 Cylindrical Roller NTN open CN 1470 2560 70800
NN3060K Cylindrical Roller NTN open CN 1470 2560 68600
SL183060-TB Cylindrical Roller FAG open CN 2020 3300 66600

Note: catalogue dynamic load ratings for this envelope span 1370.0– 2400.0 kN — a 75% spread between designs in the very same 300×460×118 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 300 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23060, 23060-CCK-W33, 23060EMD1, 23060EMKD1, 323060UTG, 413060UTG, C3060-KM, C3060-M, NCF3060-CV, NN3060, NN3060K, SL183060-TB.

Frequently asked questions

Are all 300×460×118 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 300 mm bore, 460 mm OD, 118 mm width (11.811×18.110×4.646 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 12 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 300×460×118?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 300×460×118 mm in inches?

300×460×118 mm converts to 11.811×18.110×4.646 in, with a 80 mm (3.150 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23060, 23060-CCK-W33, 23060EMD1 mount in the same space despite different internal designs.