380×560×135 mm bearings

11 models from 3 brands across 4 types share this ISO 15 envelope: 380 mm bore, 560 mm outside diameter, 135 mm width (14.961×22.047×5.315 in), 90 mm radial section.

11 models fit this space 3 brands 11 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23076EMD1 Spherical Roller NTN open CN 3230 5270 117000
23076EMKD1 Spherical Roller NTN open CN 3230 5270 113000
323076 Tapered Roller NTN open CN 2310 4350 110000
413076UTG Tapered Roller NTN open CN 2170 3350 100000
C3076-KM CARB Toroidal Roller SKF open CN 3000 5200 110000
C3076-M CARB Toroidal Roller SKF open CN 3000 5200 110000
NCF3076-V Cylindrical Roller SKF open CN 2700 5100 110000
NN3076 Cylindrical Roller NTN open CN 1870 3450 113000
NN3076K Cylindrical Roller NTN open CN 1870 3450 109000
NU3076-ECMP Cylindrical Roller SKF open CN 2380 4750 109000
SL183076-TB Cylindrical Roller FAG open CN 2600 4450 106000

Note: catalogue dynamic load ratings for this envelope span 1870.0– 3230.0 kN — a 73% spread between designs in the very same 380×560×135 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 380 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23076EMD1, 23076EMKD1, 323076, 413076UTG, C3076-KM, C3076-M, NCF3076-V, NN3076, NN3076K, NU3076-ECMP, SL183076-TB.

Frequently asked questions

Are all 380×560×135 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 380 mm bore, 560 mm OD, 135 mm width (14.961×22.047×5.315 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 11 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 380×560×135?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 380×560×135 mm in inches?

380×560×135 mm converts to 14.961×22.047×5.315 in, with a 90 mm (3.543 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23076EMD1, 23076EMKD1, 323076 mount in the same space despite different internal designs.