323076 bearing: complete specifications & equivalents
The 323076 is a ANSI ABMA 19.2 radial bearing sized 380 x 560 x 135 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 380 mm |
| Outer diameter D | 560 mm |
| Width B | 135 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 2310 kN |
| Basic static load rating C0 | 4350 kN |
| Fatigue load limit Pu | 335 kN |
| Limiting speed (mechanical) | 440 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 110000 g |
| Manufacturer designation | NTN 4T-323076 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-432-series range
| Bore d | 14.961 in |
|---|---|
| Outer diameter D | 22.047 in |
| Width B | 5.315 in |
| ISO bore code | 76 |
| Radial section height (D−d)/2 | 90 mm |
| Smallest bore in 4t-432-series | 40 mm |
| Largest outer diameter in 4t-432-series | 790 mm |
| Width range across 4t-432-series | 46–266 mm |
| Bore position in 4t-432-series (smallest first) | 33 of 39 |
| Bore above smallest 4t-432-series size | 340 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 323076 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 323076 model number is decoded
4T-323076 belongs to the heavy-duty 432-family TDO double-row series of NTN double-row tapered roller bearings; the unit is mounted as one article and its internal clearance is set at the factory, not on the shaft. With no letter suffix, 323076 is the basic open double-row execution: steel cages, factory-set internal clearance, no feature suffix in the order code. Double-row capacity is not twice a single-row bearing: the printed 2310 kN C already accounts for load sharing between the two rows of 4T-323076, so apply it directly in the L10 calculation. TDO construction means the two cone assemblies of 4T-323076 face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 380 mm shaft. Do not separate the cones from the double cup at inspection unless re-matching is guaranteed — the rows of 4T-323076 are ground as a unit.
Typical equipment & failure modes
Common applications
- heavy press and forging-machine drives
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- pressed-steel cage pocket wear from roller skid at light load and high speed
- water-induced pitting when washdown reaches the open unit without external seals
Selection pitfalls — read before you substitute
- At 380 mm bore the 4T-323076 unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 2310 kN C level.
- The 432 heavy plan gives 4T-323076 its 135 mm width and 2310 kN rating at the 380 mm bore; do not downgrade to a 430-family unit of the same bore without re-checking C, C0 and the 335 kN Cu.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-323076 feeds the two roller complements evenly; a single-side feed starves the far row.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-323076 feeds the two roller complements evenly; a single-side feed starves the far row.
- The internal clearance of 4T-323076 is factory-set: no end-play adjustment exists at mounting, and any attempt to set preload with a shaft nut overloads one row.
- The 2310/4350 kN ratings and 335 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-323076; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-323076?
4T-323076 is a double-row tapered roller bearing of TDO (back-to-back) construction: 380 mm bore, 560 mm outside diameter and 135 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 2310 kN, C0 4350 kN, Cu 335 kN, grease limiting speed 440 r/min, oil speed 580 r/min, mass about 110 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 380 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-323076 belongs to the heavy-duty 432-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-323076 be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 135 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 323076 mean?
With no letter suffix, 323076 is the basic open double-row execution: steel cages, factory-set internal clearance, no feature suffix in the order code.
Why does 4T-323076 list two speeds, 440 and 580 r/min?
The lower figure, 440 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-323076 at 580 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.