323080UTG bearing: complete specifications & equivalents
The 323080UTG is a ANSI ABMA 19.2 radial bearing sized 400 x 600 x 148 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 400 mm |
| Outer diameter D | 600 mm |
| Width B | 148 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 3250 kN |
| Basic static load rating C0 | 5450 kN |
| Fatigue load limit Pu | 410 kN |
| Limiting speed (mechanical) | 410 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 150000 g |
| Manufacturer designation | NTN 4T-323080UTG |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-432-series range
| Bore d | 15.748 in |
|---|---|
| Outer diameter D | 23.622 in |
| Width B | 5.827 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 100 mm |
| Smallest bore in 4t-432-series | 40 mm |
| Largest outer diameter in 4t-432-series | 790 mm |
| Width range across 4t-432-series | 46–266 mm |
| Bore position in 4t-432-series (smallest first) | 34 of 39 |
| Bore above smallest 4t-432-series size | 360 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 323080UTG | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 323080UTG model number is decoded
4T-323080UTG is the NTN 4T catalogue entry for a 400×600×148 mm double-row tapered roller bearing — the TDO arrangement reacts radial load plus thrust in both directions without a second bearing. The 4T- prefix is NTN's tapered roller quality mark; 430 numbers the light TDO plan and 432 the heavy TDO plan — at the same 400 mm bore the 432 execution carries a wider, heavier section than the 430. Axial capacity is bidirectional because the rows are opposed: 4T-323080UTG locates the shaft in both directions with C0 5450 kN behind the static check of the more heavily loaded row. Because the unit is preset, mounting 4T-323080UTG resembles mounting a double-row spherical or cylindrical bearing: seat the unit, clamp axially to the stated end cover torque, and verify rotation — no end-play measurement is required. Axial clamping of the double cup must be uniform around the 600 mm OD; a cocked end cover pinches one row and destroys the factory clearance setting.
Typical equipment & failure modes
Common applications
- mine hoist and dragline drum shafts
- cement-plant mill and kiln drive trains
- port-crane hoist and luffing gearboxes
- heavy press and forging-machine drives
Known failure patterns
- edge loading on one row when the housing seats the double cup cocked across its width
- brinelling of both rows from a mounting blow transmitted through the roller complements
- preload loss and hammering noise when the cup clamping loosens and the unit gains axial float
- cage damage when the unit is lifted by one cone instead of the double cup during fitting
- rolling-contact fatigue spalling after the catalogue L10 life at the actual combined load
Selection pitfalls — read before you substitute
- At 400 mm bore the 4T-323080UTG unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 3250 kN C level.
- The 432 heavy plan gives 4T-323080UTG its 148 mm width and 3250 kN rating at the 400 mm bore; do not downgrade to a 430-family unit of the same bore without re-checking C, C0 and the 410 kN Cu.
- The internal clearance of 4T-323080UTG is factory-set: no end-play adjustment exists at mounting, and any attempt to set preload with a shaft nut overloads one row.
- The 100.0 mm section leaves little room for oversized shaft fillets; follow the 2203E chamfer table for 4T-323080UTG or the cones bottom out on the radius.
- At inspection do not mix the cone assemblies of 4T-323080UTG with another unit; rows are ground together and re-matching is not guaranteed in the field.
- The 3250/5450 kN ratings and 410 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-323080UTG; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-323080UTG?
4T-323080UTG is a double-row tapered roller bearing of TDO (back-to-back) construction: 400 mm bore, 600 mm outside diameter and 148 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 3250 kN, C0 5450 kN, Cu 410 kN, grease limiting speed 410 r/min, oil speed 580 r/min, mass about 150 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 400 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-323080UTG belongs to the heavy-duty 432-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-323080UTG be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 148 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 323080UTG mean?
Suffix reading on 323080UTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-323080UTG list two speeds, 410 and 580 r/min?
The lower figure, 410 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-323080UTG at 580 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.