710×1030×315 mm bearings
4 models from 2 brands across 2 types share this ISO 15 envelope: 710 mm bore, 1030 mm outside diameter, 315 mm width (27.953×40.551×12.402 in), 160 mm radial section.
4 models fit this space 2 brands 4 with catalogue C rating
Dimensional interchange — verify before substituting
These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.
| Model | Type | Brand | Seal | Clearance | C (kN) | C0 (kN) | Mass (g) |
|---|---|---|---|---|---|---|---|
| 240-710B | Spherical Roller | NTN | open | CN | 10300 | 22500 | 884000 |
| 240-710BK30 | Spherical Roller | NTN | open | CN | 10300 | 22500 | 870000 |
| C40-710-K30M | CARB Toroidal Roller | SKF | open | CN | 10600 | 21600 | 865000 |
| C40-710-M | CARB Toroidal Roller | SKF | open | CN | 10600 | 21600 | 865000 |
Substitution verification checklist
- Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
- Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
- Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
- Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
- Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.
Browse all 710 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 240-710B, 240-710BK30, C40-710-K30M, C40-710-M.
Frequently asked questions
Are all 710×1030×315 mm bearings interchangeable?
They share the same ISO 15 boundary dimensions — 710 mm bore, 1030 mm OD, 315 mm width (27.953×40.551×12.402 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 4 models listed here and must be checked against the duty before substitution.
Is it a drop-in replacement if two bearings both measure 710×1030×315?
Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.
What is 710×1030×315 mm in inches?
710×1030×315 mm converts to 27.953×40.551×12.402 in, with a 160 mm (6.299 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 240-710B, 240-710BK30, C40-710-K30M mount in the same space despite different internal designs.