7022-NTN bearing: complete specifications & equivalents
The 7022-NTN is a ISO 15 radial bearing sized 110 x 170 x 28 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 110 mm |
| Outer diameter D | 170 mm |
| Width B | 28 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 102 kN |
| Basic static load rating C0 | 93 kN |
| Fatigue load limit Pu | 5.5 kN |
| Limiting speed (mechanical) | 3900 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 2300 g |
| Manufacturer designation | NTN 7022 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 7000-series range
| Bore d | 4.331 in |
|---|---|
| Outer diameter D | 6.693 in |
| Width B | 1.102 in |
| ISO bore code | 22 |
| Radial section height (D−d)/2 | 30 mm |
| Smallest bore in 7000-series | 10 mm |
| Largest outer diameter in 7000-series | 420 mm |
| Width range across 7000-series | 8–65 mm |
| Bore position in 7000-series (smallest first) | 23 of 36 |
| Bore above smallest 7000-series size | 100 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 7022 | GENERIC-ISO | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 7022-NTN model number is decoded
The standard-section 7000 single-row family entry 7022 carries a 110 mm bore in a 170 mm outside diameter, 28 mm wide envelope. The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 93 kN versus C 102 kN, is what supports slow oscillating duty and shock without immediate brinelling. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 110 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it.
Typical equipment & failure modes
Common applications
- paper-machine roll and calendar drives
- extruder and mixer gearbox output shafts
- mining conveyor head-shaft positions
- marine auxiliary and winch gearbox shafts
Known failure patterns
- false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch
- loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow
- machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface
- lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated
- lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated
Selection pitfalls — read before you substitute
- Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.
- The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.
- Never use a four-point or double-row bearing as a like-for-like swap for a single 7022 without re-checking axial float, heat and housing width — the kinematics differ.
- Grease rated for deep-groove motor duty is not automatically right at 3,900 r/min with preload; check the grease speed factor against the catalogue figure.
- Do not pair two random 7022 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.
- The 102/93 kN ratings and 5.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7022; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 7022?
7022 is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 170 mm outside diameter, 28 mm width (4.331 x 6.693 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 102 kN, C0 93 kN and a 5.5 kN fatigue load limit Pu; the grease limiting speed is 3,900 r/min and the oil rating 5,300 r/min; mass about 2300 g.
How is the 7022 designation structured?
70 is the single-row dimension series (standard-section 7000 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 170 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series.
Which axial direction does 7022 support?
One 7022 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact.
What lubrication speeds does NTN print for 7022?
Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,900 r/min and the oil rating 5,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit.
What should be checked before substituting another make for 7022?
The 110/170/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 102 kN / C0 93 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.