7210-BECBP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7210-BECBP model number is decoded

7210 BECBP is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 50×90×20 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 40 kN, C0 31 kN, Pu 1.32 kN.reference speed 9,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), which coincide for this size, catalogue mass 470 g. Envelope economics: the 20 mm width over a 20.0 mm section yields 1.00 mm of ring width per section millimetre, and the bearing weighs 470 g for 40 kN of dynamic capacity — about 12 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min while thermal balance under catalogue load sets the 9,000 r/min reference; at dm ≈ 70.0 mm the corresponding dn is approximately 630k mm·r/min. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 20 mm width gives a bore/width ratio of 2.50; use these ratios when housing space around the 50 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• One 7210-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.
• Fillet radii must clear the chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
• Assign interference to the rotating ring — roughly k5 on a 50 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• The steep 40° angle of 7210-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.