7312-BECBM bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7312-BECBM model number is decoded

7312 BECBM is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 60×130×31 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 104 kN, C0 76.5 kN, Pu 3.2 kN.reference speed 6,300 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 1750 g. At the printed limiting speed of 8,500 r/min the mean pitch diameter dm ≈ 95.0 mm implies a dn value around 808k mm·r/min; the 6,300 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 31 mm width over a 35.0 mm section yields 0.89 mm of ring width per section millimetre, and the bearing weighs 1750 g for 104 kN of dynamic capacity — about 17 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 8,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.74. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.
• Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• At 60 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.
• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• The steep 40° angle of 7312-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.