7316-BEM bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7316-BEM model number is decoded

7316 BEM is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 80×170×39 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 135 kN, C0 110 kN, Pu 4.15 kN.reference speed 5,000 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 3800 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,800 r/min while thermal balance under catalogue load sets the 5,000 r/min reference; at dm ≈ 125.0 mm the corresponding dn is approximately 600k mm·r/min. Sizing arithmetic on the 80 mm bore: 135 kN C divided by the 45.0 mm radial section height gives 3.0 kN per section millimetre; the 3800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 4,800 r/min limiting speed, i.e. a reference-to-limit ratio of 1.04. Ordering note: BEM pairs the optimized 40-degree geometry with a machined one-piece brass window cage as a basic (non-universal) single bearing; it is the brass-cage counterpart of the polymer BEP, and universally matchable positions must use the BECBM or BCBM execution instead.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Preload the set against a calculated stand-off dimension — the ground faces of BEM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.
• At 80 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.
• Do not mix execution classes inside one set: a universally matchable BEM unit is ground for arbitrary pairing, a basic execution is not.
• Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.
• The steep 40° angle of 7316-BEM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for 7316 BEM as the single basic machined brass execution; the other order numbers of the 7316 size are different products and may carry different ratings — always quote the full designation when purchasing.