7322-NTN bearing: complete specifications & equivalents
The 7322-NTN is a ISO 15 radial bearing sized 110 x 240 x 50 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 110 mm |
| Outer diameter D | 240 mm |
| Width B | 50 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 273 kN |
| Basic static load rating C0 | 246 kN |
| Fatigue load limit Pu | 14.5 kN |
| Limiting speed (mechanical) | 3200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 9600 g |
| Manufacturer designation | NTN 7322 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 7300-series range
| Bore d | 4.331 in |
|---|---|
| Outer diameter D | 9.449 in |
| Width B | 1.969 in |
| ISO bore code | 22 |
| Radial section height (D−d)/2 | 65 mm |
| Smallest bore in 7300-series | 10 mm |
| Largest outer diameter in 7300-series | 420 mm |
| Width range across 7300-series | 11–80 mm |
| Bore position in 7300-series (smallest first) | 23 of 32 |
| Bore above smallest 7300-series size | 100 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 7322 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 7322-BECBM | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 7322-BECBP | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 7322-BECBY | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 7322-BEM | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 7322-BEY | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 7322-NTN model number is decoded
At 110 x 240 x 50 mm, NTN 7322 sits in the heavy-duty 7300 single-row family of the angular-contact programme. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 273 kN and C0 246 kN, each mm of bore carries about 2.48 kN of dynamic rating. Against a deep-groove bearing of the same 110 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 110 mm bore give the working limits.
Typical equipment & failure modes
Common applications
- crane and hoist gearbox shafts
- paper-machine roll and calendar drives
- extruder and mixer gearbox output shafts
- mining conveyor head-shaft positions
Known failure patterns
- false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch
- thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear
- pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed
- edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face
- contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue
Selection pitfalls — read before you substitute
- Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.
- The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.
- The 3,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.
- Do not pair two random 7322 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.
- On a 110 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.
- The 273/246 kN ratings and 14.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7322; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 7322?
7322 is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 240 mm outside diameter, 50 mm width (4.331 x 9.449 x 1.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 273 kN, C0 246 kN and a 14.5 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min; mass about 9600 g.
How is the 7322 designation structured?
73 is the single-row dimension series (heavy-duty 7300 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 240 mm OD and 50 mm width follow the ISO 15 boundary-dimension plan for that series.
Which axial direction does 7322 support?
One 7322 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact.
What lubrication speeds does NTN print for 7322?
Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit.
What should be checked before substituting another make for 7322?
The 110/240/50 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 273 kN / C0 246 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.