QJ-215-MA bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the QJ-215-MA model number is decoded

QJ 215 MA is SKF's 75 mm-bore QJ four-point contact ball bearing of the QJ200 series, 75×130×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 125 kN, C0 132 kN, Pu 5.6 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 1450 g. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 1450 g for 125 kN of dynamic capacity — about 12 g per rated kN. Mass and section check: 1450 g inside the 75×130×25 mm outline leaves a 27.5 mm radial section, and the 132 kN static rating is 1.06× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,500 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring
• Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.
• Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.
• Anti-rotation is NOT built into QJ-215-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.
• The MA brass cage of QJ-215-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 215 MA as the qj plain execution; the other order numbers of the QJ 215 size are different products and may carry different ratings — always quote the full designation when purchasing.