QJ-215-N2MA bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the QJ-215-N2MA model number is decoded

QJ 215 N2MA is SKF's 75 mm-bore QJ four-point contact ball bearing of the QJ200 series, 75×130×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 125 kN, C0 132 kN, Pu 5.6 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 1450 g. Sizing arithmetic on the 75 mm bore: 125 kN C divided by the 27.5 mm radial section height gives 4.5 kN per section millimetre; the 1450 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 1450 g for 125 kN of dynamic capacity — about 12 g per rated kN. Bore-to-OD planning: OD 130 over bore 75 is a 1.73× step for this size, and the 25 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 75 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.
• Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.
• Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat
• Anti-rotation is built into QJ-215-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.
• The MA brass cage of QJ-215-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 215 N2MA as the qj slotted execution; the other order numbers of the QJ 215 size are different products and may carry different ratings — always quote the full designation when purchasing.