16005-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 16005-NTN model number is decoded

In the 16000-series (the narrow extra-light section of ISO 15) the last two digits encode the bore: 16005 carries bore code 05 = 25 mm. Outside diameter 47 mm and width 8 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 25 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 16005-NTN; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
• Because the 160xx narrow section shares the 47 mm OD of the 6005 at 25 mm bore but is only 8 mm wide, a housing machined for the wider bearing needs a spacer or relocated circlip — never assume width interchangeability.
• The open 16005-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 25×47×8 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 16005-NTN leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 47 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 16005-NTN.
• The housing bore for the 47 mm OD should be round within IT7; an oval bore pinches the outer ring of 16005-NTN and shows up later as two-point loaded raceway wear.
• The open 16005 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 25 mm bore puts 16005 in NTN's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• NTN rates 16005 at 15000 r/min grease limiting speed — this is an electric-motor range; keep the grease fill at 25–35% of the free bearing volume and avoid mixing grease thickener types if regreasing through the housing.
• NTN rates 16005 at 9.25 kN dynamic (C) and 5.1 kN static (C0), 0.4 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 60 g, 16005 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 25×47×8 mm envelope of 16005 gives a D/d ratio of 1.88 and 11.0 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 9.25/5.1 kN load ratings, 0.4 kN fatigue load limit Cu NTN lists the grease limiting speed at 15000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 60 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 16005 on the 25×47×8 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 16005 in a rated drive.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.