16005 bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 16005 model number is decoded

16005 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the narrow 160xx section of the ISO 15 general plan, multiplying bore code 05 by five gives the 25 mm bore; the 47 mm outside diameter and 8 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 25 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 25 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 16005.
• Because the 160xx narrow section shares the 47 mm OD of the 6005 at 25 mm bore but is only 8 mm wide, a housing machined for the wider bearing needs a spacer or relocated circlip — never assume width interchangeability.
• The open 16005 has no lubricant retention: grease escapes and contaminants migrate straight into the 25×47×8 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 16000-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 16005 units.
• Do not quieten a noisy bearing by preloading it: the 16000-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• A 25 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• The open 16005 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• FAG rates 16005 at 22200 r/min mechanical limiting speed (thermal reference speed 11600 r/min) — a high-speed range where the thermal reference speed governs continuous duty; use low-viscosity turbine oil or high-speed grease and avoid lip-contact seals entirely.
• The 25 mm bore puts 16005 in Schaeffler's light industrial range; the standard cage and CN clearance cover most fractional-horsepower motor and small-pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• FAG rates 16005 at 8.86 kN dynamic (C) and 5.61 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At 53 g, 16005 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 25×47×8 mm envelope of 16005 gives a D/d ratio of 1.88 and 11.0 mm radial section height — a standard FAG medium section balancing load capacity and speed; the standard cage is adequate up to the listed speeds and C3 clearance is the common hot-shaft choice.
• The 8.86/5.61 kN load ratings, mass 53 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 16005 on the 25×47×8 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 16005 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Mixing old and new FAG generations of the same designation in one arrangement is dimensionally acceptable, but where ratings matter — preloaded or matched sets — order both positions from the same generation and lot.
• Schaeffler's medias/eKatalog is the live source for the current execution of 16005: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.