4212-ATN9 bearing: complete specifications & equivalents
The 4212-ATN9 is a ISO 15 radial bearing sized 60 x 110 x 28 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 60 mm |
| Outer diameter D | 110 mm |
| Width B | 28 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 57.2 kN |
| Basic static load rating C0 | 55 kN |
| Fatigue load limit Pu | 2.36 kN |
| Reference speed (thermal) | 9500 rpm |
| Limiting speed (mechanical) | 5300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1100 g |
| Manufacturer designation | 4212 ATN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 4200-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 1.102 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 25 mm |
| Smallest bore in 4200-series | 10 mm |
| Largest outer diameter in 4200-series | 160 mm |
| Width range across 4200-series | 14–40 mm |
| Bore position in 4200-series (smallest first) | 13 of 19 |
| Bore above smallest 4200-series size | 50 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 62212-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 60×110×28 mm envelope as SKF 62212-2RS1, but catalogue C/C0 differ (57.2/55 kN vs 52.7/36 kN) — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 4212-ATN9 model number is decoded
4212 ATN9 is a double-row deep-groove ball bearing in the 4200-series: the last two digits encode the bore: 4212 carries code 12 = 60 mm (code × 5). Two complete ball sets share the 60×110×28 mm (2.362×4.331×1.102 in) envelope, giving C 57.2 kN, C0 55 kN and Pu 2.36 kN, with reversing axial capacity a single-row bearing cannot match. ATN9 is the glass-fibre PA66 cage. Limiting speed 5300 r/min, mass 1100 g. The arrangement is open and requires external sealing.
Typical equipment & failure modes
Common applications
- agricultural gearboxes
- belt take-up and tensioner units
- machine tool feed drives
- lifting and hoisting gear
Known failure patterns
- uneven load sharing between the two raceways when one ring is tilted
- polyamide cage embrittlement after sustained high-temperature service
- raceway smearing under marginal lubrication at start-up
- electrical pitting in VFD-driven motors without shaft grounding
Selection pitfalls — read before you substitute
- Fit both rings square on the shoulders: the narrow internal land between the two raceways of 4212-ATN9 is sensitive to cocking during pressing.
- The ATN9 cage is glass-fibre-reinforced polyamide 66: it is light and quiet but caps continuous service around 100–120 °C in oil/grease — above that use the pressed-steel or machined-cage version of the 60 mm position.
- Two deep-groove raceways in 4212-ATN9 share the load but need parallel seats; tilting the 28 mm-wide assembly loads one row heavily and can spall it early.
- The wide 60×110×28 mm envelope is not interchangeable with a single-row 6212 — the housing and shaft shoulders differ, so design the seat for the double-row width from the start.
- The wide 60×110×28 mm envelope is not interchangeable with a single-row 6212 — the housing and shaft shoulders differ, so design the seat for the double-row width from the start.
- Clearance suffixes follow the seal code in the designation stack (e.g. 4212-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
Frequently asked questions
What are the dimensions of 4212-ATN9?
Double-row 4212 ATN9 measures 60×110×28 mm (2.362×4.331×1.102 in), about 1100 g.
What does ATN9 mean on 4212 ATN9?
A = double-row deep-groove arrangement, TN9 is a glass-fibre-reinforced polyamide 66 cage; it limits continuous temperature to roughly 100–120 °C.
What load does 4212-ATN9 carry?
C 57.2 kN, C0 55 kN and Pu 2.36 kN per catalogue 17000; both rows share the load when the rings sit parallel.
Why choose a double-row 42xx/43xx bearing?
Two ball rows give higher C (57.2 kN for 4212-ATN9), reversing axial capacity and some moment stiffness in one 28 mm-wide unit — useful on gearbox layshafts and pump shafts.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.