60-800-N1MAS bearing: complete specifications & equivalents

The 60-800-N1MAS is a ISO 15 radial bearing sized 800 x 1150 x 155 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 1150 mm d = 800 B = 155 mm side section front view
Principal dimensions: bore d 800 mm, outer diameter D 1150 mm, width B 155 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 800 mm
Outer diameter D 1150 mm
Width B 155 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 1010 kN
Basic static load rating C0 2550 kN
Fatigue load limit Pu 34.5 kN
Reference speed (thermal) 900 rpm
Limiting speed (mechanical) 750 rpm
Operating temperature -40 to +120 °C
Mass 523000 g
Manufacturer designation 60/800 N1MAS
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6000-series range

Bore d31.496 in
Outer diameter D45.276 in
Width B6.102 in
ISO bore code—
Radial section height (D−d)/2175 mm
Smallest bore in 6000-series4 mm
Largest outer diameter in 6000-series1150 mm
Width range across 6000-series4–155 mm
Bore position in 6000-series (smallest first)61 of 61
Bore above smallest 6000-series size796 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 60-800-N1MAS model number is decoded

In the large-bore 6000-series, the bore is written directly after the slash as 800 mm (large thin-section bores use the slash spelling instead of the two-digit code). The envelope is 800×1150×155 mm (31.496×45.276×6.102 in) with a 175.0 mm radial section height, C 1010 kN, C0 2550 kN and Pu 34.5 kN. The open 60/800 N1MAS carries no shields or seals and relies on application lubrication and external sealing. The N1MAS suffix identifies the machined brass cage execution (special cage variant for this large thin-section size), a separate order number from the pressed-steel version. Limiting speed 750 r/min, catalogue mass 523000 g.

Typical equipment & failure modes

Common applications

  • large industrial gearboxes
  • heavy conveyor drives
  • hoists and winches
  • industrial fans and blowers

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Do not preload 60-800-N1MAS to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • The fatigue load limit is 34.5 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • The N1MAS execution of 60-800-N1MAS is a special machined-brass cage variant listed in catalogue 17000 for the largest thin-section sizes; confirm the exact cage feature set with SKF when ordering and servicing.
  • The N1MAS suffix on 60-800-N1MAS denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 523000 g quoted mass includes the heavier cage.
  • Open 60-800-N1MAS needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 60-800-N1MAS; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.

Frequently asked questions

What are the dimensions of 60-800-N1MAS?

The SKF 60/800 N1MAS measures 800 mm bore × 1150 mm OD × 155 mm width (31.496 × 45.276 × 6.102 in), mass about 523000 g. It is open, with no shields or seals.

Why is there a slash in the designation 60/800 N1MAS?

The slash writes a bore that falls outside the two-digit code table: 60/800 means 800 mm bore. The site slug 60-800-N1MAS replaces the slash with a hyphen.

What internal clearance does 60-800-N1MAS have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 60-800-N1MAS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 60-800-N1MAS take?

Catalogue values for 60/800 N1MAS: dynamic C 1010 kN, static C0 2550 kN, fatigue limit Pu 34.5 kN. Use C in life calculation and C0 for static checks at 800 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.