6001-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6001-FAG model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6001 carries bore code 12 = 12 mm. Outside diameter 28 mm and width 8 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 12 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 12 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6001 with C3 clearance and re-check the residual value after mounting.
• The 60xx extra-light section at 12 mm bore uses a smaller 28 mm OD than a 6212; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
• The open 6001-FAG has no lubricant retention: grease escapes and contaminants migrate straight into the 12×28×8 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6000-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6001 units.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 8 mm-wide ring of 6001-FAG drags the lip and overheats it.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• The open 6001 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• The 42500 r/min mechanical limiting speed puts 6001 at the top of the HR 1 deep-groove speed range (thermal reference speed 26000 r/min); at these speeds cage design and grease shear dominate — run open with oil-mist or air-over-oil lubrication and verify the thermal reference speed for the actual load before committing.
• At 12 mm bore the 6001 sits in Schaeffler's small-bore range; HR 1 ships these sizes with a pressed steel or plastic cage and P0 tolerance as standard — for instrument or spindle accuracy order the P6/P5 variant explicitly, since P0 runout figures will not hold.
• FAG rates 6001 at 5.9 kN dynamic (C) and 2.37 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At only 19 g, 6001 is a lightweight FAG bearing that can be handled by hand; still press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 12×28×8 mm envelope of 6001 gives a D/d ratio of 2.33 and 8.0 mm radial section height — a heavy FAG section for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 5.9/2.37 kN load ratings, mass 19 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6001-C on the 12×28×8 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6001 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• For hot shafts above roughly 100 °C continuous, consult Schaeffler about seal material and grease options for the 2RSR execution of 6001; the standard NBR lip is the economical general-duty choice, not the high-temperature one.
• Mixing old and new FAG generations of the same designation in one arrangement is dimensionally acceptable, but where ratings matter — preloaded or matched sets — order both positions from the same generation and lot.