6001-ZZ bearing: complete specifications & equivalents
The 6001-ZZ is a ISO 15 radial bearing sized 12 x 28 x 8 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 12 mm |
| Outer diameter D | 28 mm |
| Width B | 8 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 5.4 kN |
| Basic static load rating C0 | 2.36 kN |
| Fatigue load limit Pu | 0.1 kN |
| Reference speed (thermal) | 60000 rpm |
| Limiting speed (mechanical) | 30000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 22 g |
| Manufacturer designation | SKF 6001-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6000-series range
| Bore d | 0.472 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.315 in |
| ISO bore code | 01 |
| Radial section height (D−d)/2 | 8 mm |
| Smallest bore in 6000-series | 10 mm |
| Largest outer diameter in 6000-series | 420 mm |
| Width range across 6000-series | 8–65 mm |
| Bore position in 6000-series (smallest first) | 2 of 35 |
| Bore above smallest 6000-series size | 2 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6001 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range. Brand-specific OEM equivalents pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6001-ZZ model number is decoded
In the 6000-series (ISO 15 diameter series 0) the last two digits encode the bore: 6001 carries bore code 01 = 12 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 28 mm and width 8 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 12 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- domestic appliances
- power tools
- small fans and blowers
- garden equipment
Known failure patterns
- fine-particle abrasion when non-contact shields let dust past in dirty duty
- grease aging in the shield-for-life cavity with no relubrication path
- cage damage from operation beyond the limiting speed
- electrical pitting in VFD-driven motors without grounding protection
Selection pitfalls — read before you substitute
- Bore codes 00–03 use the exception table: 6001 fits a 12 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).
- The 60xx extra-light section at 12 mm bore uses a smaller 28 mm OD than a 6201; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
- ZZ shields are non-contact: 6001-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6001-2RS for that.
- Shielded 6001-ZZ units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
- Do not quieten a noisy bearing by preloading it: the 6000-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
- SKF spells the shielded version 6001-2Z (one shield: 6001-Z), not "-ZZ": the suffix language differs by brand even though the ISO envelope is identical, so quote the brand designation when ordering.
- The single-shield execution 6001-Z is a distinct order number in catalogue 17000: it suits open gears or oil-bath arrangements where the unshielded face faces the lubricant, and it is not interchangeable with the double-shield 6001-2Z for high-contamination positions.
- The 5.4/2.36 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6001-ZZ bearing?
A 6001-ZZ deep-groove ball bearing has a 12 mm bore, 28 mm outer diameter and 8 mm width (0.472 × 1.102 × 0.315 in), per ISO 15 boundary dimensions. It is fitted with two non-contact metallic shields.
Why does 6001 not follow the bore-code × 5 rule?
Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 6001 with code 01 has a 12 mm bore. The code × 5 convention starts at code 04 (20 mm).
What does the ZZ suffix on 6001-ZZ mean?
ZZ means two non-contact sheet-metal shields, one each side. They retain factory grease and block coarse particles with little friction, but do not seal against liquids, fine dust or pressure washing.
How does the 6000 compare with other series at the same 12 mm bore?
The second digit is the diameter series: 60 is the smallest standard section (28×8 mm, 8.0 mm radial section) at 12 mm bore — below 62/63/64 in load capacity, for light loads in compact spaces.
What is the SKF designation and catalogue data for 6001-ZZ?
In the SKF Rolling Bearings catalogue this size is listed as 6001-2Z — two non-contact sheet-metal shields, 12×28×8 mm per ISO 15. Quoted values: C 5.4 kN, C0 2.36 kN, Pu 0.1 kN, limiting speed 30000 r/min, mass 22 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 6001-ZZ.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.