6006-2RS-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6006-2RS-FAG model number is decoded

6006-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 06 by five gives the 30 mm bore; the 55 mm outside diameter and 13 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 30 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. Schaeffler HR 1 catalogues the lip-contact sealed version as 6006-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 6006-2RS-FAG; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
• Choosing the 60xx extra-light section saves radial space at 30 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6206 before committing to the smaller envelope.
• Contact seals add drag and heat: 6006-2RS-FAG runs slower and cooler-limited than the open 6006; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Heat is the enemy of the sealed 6006-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 13 mm-wide ring of 6006-2RS-FAG drags the lip and overheats it.
• Measure the shaft, do not trust the drawing: a 30 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6006-2RS-FAG.
• Schaeffler HR 1 lists the lip-contact sealed version as 6006-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. FAG's RSR lip material is NBR as standard — above roughly 100 °C continuous, consult Schaeffler for higher-temperature seal options.
• At 10500 r/min mechanical limiting speed, 6006 covers general-purpose motor and pump duty; keep grease fill at 25–35% of free volume and verify the housing can dissipate the frictional heat at the thermal reference speed.
• The 30 mm bore puts 6006 in Schaeffler's light industrial range; the standard cage and CN clearance cover most fractional-horsepower motor and small-pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• FAG rates 6006 at 14.5 kN dynamic (C) and 8.3 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At 113 g, 6006 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 30×55×13 mm envelope of 6006 gives a D/d ratio of 1.83 and 12.5 mm radial section height — a standard FAG medium section balancing load capacity and speed; the standard cage is adequate up to the listed speeds and C3 clearance is the common hot-shaft choice.
• The 14.5/8.3 kN load ratings, mass 113 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6006-C-2HRS on the 30×55×13 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6006 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• FAG sealed units arrive greased for life with a lithium-soap fill; Schaeffler quotes a shelf life for greased bearings and recommends running stock first-in-first-out rather than re-greasing aged sealed units.
• FAG standard tolerance for this size is P0 (PN); P6/P5 precision executions exist for spindle-adjacent duty but carry different order numbers in the Schaeffler system — they are not a selectable sorting of standard stock.