6007-2RS-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6007-2RS-FAG model number is decoded

6007-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 07 by five gives the 35 mm bore; the 62 mm outside diameter and 14 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 35 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. Schaeffler HR 1 catalogues the lip-contact sealed version as 6007-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 35 mm shaft for 6007 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• Choosing the 60xx extra-light section saves radial space at 35 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6207 before committing to the smaller envelope.
• Heat is the enemy of the sealed 6007-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 6007-2RS-FAG in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 6000-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Schaeffler HR 1 lists the lip-contact sealed version as 6007-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. FAG's RSR lip material is NBR as standard — above roughly 100 °C continuous, consult Schaeffler for higher-temperature seal options.
• At 9300 r/min mechanical limiting speed, 6007 covers general-purpose motor and pump duty; keep grease fill at 25–35% of free volume and verify the housing can dissipate the frictional heat at the thermal reference speed.
• The 35 mm bore puts 6007 in Schaeffler's general-purpose industrial range; the standard cage and CN clearance cover most electric-motor and pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• At 17.5 kN dynamic load rating (C) and 10.3 kN static (C0), 6007 is a medium-load FAG bearing for most electric-motor and pump duty; check the static safety factor against C0 for preloaded or thrust-loaded arrangements.
• At 148 g, 6007 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 35×62×14 mm envelope of 6007 gives a D/d ratio of 1.77 and 13.5 mm radial section height — a standard FAG medium section balancing load capacity and speed; the standard cage is adequate up to the listed speeds and C3 clearance is the common hot-shaft choice.
• The 17.5/10.3 kN load ratings, mass 148 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6007-C-2HRS on the 35×62×14 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6007 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Mixing old and new FAG generations of the same designation in one arrangement is dimensionally acceptable, but where ratings matter — preloaded or matched sets — order both positions from the same generation and lot.
• Schaeffler's medias/eKatalog is the live source for the current execution of 6007: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.