6008-2RS bearing: complete specifications & equivalents
The 6008-2RS is a ISO 15 radial bearing sized 40 x 68 x 15 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 40 mm |
| Outer diameter D | 68 mm |
| Width B | 15 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 17.8 kN |
| Basic static load rating C0 | 11 kN |
| Fatigue load limit Pu | 0.49 kN |
| Limiting speed (mechanical) | 6300 rpm |
| Operating temperature | -30 to +110 °C |
| Mass | 200 g |
| Manufacturer designation | SKF 6008-2RS1 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6000-series range
| Bore d | 1.575 in |
|---|---|
| Outer diameter D | 2.677 in |
| Width B | 0.591 in |
| ISO bore code | 08 |
| Radial section height (D−d)/2 | 14 mm |
| Smallest bore in 6000-series | 10 mm |
| Largest outer diameter in 6000-series | 420 mm |
| Width range across 6000-series | 8–65 mm |
| Bore position in 6000-series (smallest first) | 9 of 35 |
| Bore above smallest 6000-series size | 30 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6008 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range. Brand-specific OEM equivalents pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6008-2RS model number is decoded
In the 6000-series (ISO 15 diameter series 0) the last two digits encode the bore: 6008 carries bore code 08 = 40 mm. Outside diameter 68 mm and width 15 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 40 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. SKF's contact-seal catalogue number is 6008-2RS1 (older text: -2RS1), mapped here from the industry-neutral -2RS spelling.
Typical equipment & failure modes
Common applications
- small gearboxes
- conveyors and drives
- agricultural equipment
- fans and blowers
Known failure patterns
- seal-lip hardening and loss of pre-grease in sustained high-temperature service
- grease-life expiry in the sealed-for-life cavity (no relubrication path)
- raceway smearing under marginal lubrication at start-up
- edge loading from shaft deflection or housing misalignment
Selection pitfalls — read before you substitute
- At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 6008-2RS; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
- The 60xx extra-light section at 40 mm bore uses a smaller 68 mm OD than a 6208; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
- Contact seals add drag and heat: 6008-2RS runs slower and cooler-limited than the open 6008; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
- Never wash a sealed 6008-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
- Shaft and housing fillets must clear the bearing chamfer so the 15 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
- SKF catalogues the contact-sealed version as 6008-2RS1 (older printings may read -2RS1); it is shipped pre-greased and its 6300 r/min limiting speed is set by seal-lip drag and grease life versus the open bearing's 22000 r/min thermal reference speed. The single-seal catalogue number is 6008-RS1, used where one shaft side needs external relubrication.
- A one-seal execution 6008-RS1 exists for arrangements that lubricate through the open side; fitting 6008-2RS1 instead means lifetime grease and no external oil supply — mixing the two in the same shaft can starve the sealed position.
- The 17.8/11 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6008-2RS bearing?
A 6008-2RS deep-groove ball bearing has a 40 mm bore, 68 mm outer diameter and 15 mm width (1.575 × 2.677 × 0.591 in), per ISO 15 boundary dimensions. It is fitted with two contact rubber seals and is normally pre-greased. Geometry-based estimated mass is about 182 g for a steel-cage unit; catalogue masses vary slightly with seal and cage design.
How does the 6008 bore code work?
The last two digits of 6008 are bore code 08, giving 08 × 5 = 40 mm bore. The 68 mm outside diameter and 15 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the 2RS suffix on 6008-2RS mean?
2RS means two contact elastomer seals, one each side, usually over a lifetime grease fill. Sealing against dust and moisture is better than ZZ shields, but the lip drag lowers the speed and temperature ceiling.
How does the 6000 compare with other series at the same 40 mm bore?
The second digit is the diameter series: 60 is the smallest standard section (68×15 mm, 14.0 mm radial section) at 40 mm bore — below 62/63/64 in load capacity, for light loads in compact spaces.
What is the SKF designation and catalogue data for 6008-2RS?
In the SKF Rolling Bearings catalogue this size is listed as 6008-2RS1 — two contact elastomer seals over a lifetime grease fill, 40×68×15 mm per ISO 15. Quoted values: C 17.8 kN, C0 11 kN, Pu 0.49 kN, limiting speed 6300 r/min, mass 200 g. Brand suffixes (2Z, 2RSH) differ from the industry-neutral spelling 6008-2RS.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.