6010-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6010-NTN model number is decoded

6010 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 10 by five gives the 50 mm bore; the 80 mm outside diameter and 16 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 50 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6010 with C3 for those conditions.
• Choosing the 60xx extra-light section saves radial space at 50 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6210 before committing to the smaller envelope.
• Storage matters for open bearings: 6010-NTN leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 6000-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6010 units.
• A 50 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• Shaft and housing fillets must clear the bearing chamfer so the 16 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• The open 6010 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 50 mm bore puts 6010 in NTN's general-purpose industrial range; the standard pressed-steel cage and CN clearance cover most electric-motor and pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• At 8400 r/min the grease limiting speed for 6010 covers most general-purpose industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• At 24.2 kN dynamic load rating (C) and 16.6 kN static (C0), 1.24 kN fatigue load limit Cu, 6010 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 261 g, 6010 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 50×80×16 mm envelope of 6010 gives a D/d ratio of 1.60 and 15.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 24.2/16.6 kN load ratings, 1.24 kN fatigue load limit Cu NTN lists the grease limiting speed at 8400 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 261 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6010 on the 50×80×16 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6010 in a rated drive.
• Order the C3 internal-clearance version (6010 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.