6013-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6013-ZZ-NTN model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6013 carries bore code 13 = 65 mm. Outside diameter 100 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 65 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN catalogue order number: 6013ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 65 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6013 with C3 clearance and re-check the residual value after mounting.
• The 60xx extra-light section at 65 mm bore uses a smaller 100 mm OD than a 6213; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
• ZZ shields are non-contact: 6013-ZZ-NTN blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6013-2RS for that.
• Do not wash 6013-ZZ-NTN in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6013-ZZ-NTN-C3. No clearance suffix means normal CN clearance.
• Never mix components between two 6013-ZZ-NTN units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• NTN catalogues the shielded version as 6013ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• At 65 mm bore 6013 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 6500 r/min the grease limiting speed for 6013 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• At 34 kN dynamic load rating (C) and 25.2 kN static (C0), 1.83 kN fatigue load limit Cu, 6013 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 421 g, 6013 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 65×100×18 mm envelope of 6013 gives a D/d ratio of 1.54 and 17.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 34/25.2 kN load ratings, 1.83 kN fatigue load limit Cu NTN lists the grease limiting speed at 6500 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 421 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6013ZZ on the 65×100×18 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6013 in a rated drive.
• Order the C3 internal-clearance version (6013 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 6013 is listed.