6013 bearing: complete specifications & equivalents
The 6013 is a ISO 15 radial bearing sized 65 x 100 x 18 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 65 mm |
| Outer diameter D | 100 mm |
| Width B | 18 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 31.9 kN |
| Basic static load rating C0 | 25 kN |
| Fatigue load limit Pu | 1.06 kN |
| Reference speed (thermal) | 14000 rpm |
| Limiting speed (mechanical) | 9000 rpm |
| Operating temperature | -40 to +150 °C |
| Mass | 440 g |
| Manufacturer designation | SKF 6013 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6000-series range
| Bore d | 2.559 in |
|---|---|
| Outer diameter D | 3.937 in |
| Width B | 0.709 in |
| ISO bore code | 13 |
| Radial section height (D−d)/2 | 17.5 mm |
| Smallest bore in 6000-series | 4 mm |
| Largest outer diameter in 6000-series | 1150 mm |
| Width range across 6000-series | 4–155 mm |
| Bore position in 6000-series (smallest first) | 20 of 61 |
| Bore above smallest 6000-series size | 61 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6013 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
| 6013-2RS-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×100×18 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty. |
| 6013-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6013-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×100×18 mm envelope per ISO 15; seal variant differs (OPEN vs RSR) — confirm sealing suits the duty. |
| 6013-ZZ-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×100×18 mm envelope per ISO 15; seal variant differs (OPEN vs ZZ) — confirm sealing suits the duty. |
| 6013-2RS-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×100×18 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty. |
| 6013-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6013-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×100×18 mm envelope per ISO 15; seal variant differs (OPEN vs RSR) — confirm sealing suits the duty. |
| 6013-ZZ-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×100×18 mm envelope per ISO 15; seal variant differs (OPEN vs ZZ) — confirm sealing suits the duty. |
| 6013-M | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF 6013 M (machined brass cage, open arrangement) is the same-size execution on the 65×100×18 mm envelope with ratings within 10 % — boundary dimensions interchangeable. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6013 model number is decoded
6013 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 13 by five gives the 65 mm bore; the 100 mm outside diameter and 18 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 65 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the SKF catalogue this open execution carries the bare designation; protected variants are ordered separately as -2Z and -2RSH.
Typical equipment & failure modes
Common applications
- gearboxes and speed reducers
- conveyor drives
- material-handling equipment
- industrial fans
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- raceway smearing under marginal lubrication at start-up
- edge loading from shaft deflection or housing misalignment
Selection pitfalls — read before you substitute
- Interference on a 65 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6013 with C3 clearance and re-check the residual value after mounting.
- The 60xx extra-light section at 65 mm bore uses a smaller 100 mm OD than a 6213; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
- The open 6013 has no lubricant retention: grease escapes and contaminants migrate straight into the 65×100×18 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Storage matters for open bearings: 6013 leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
- Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
- Do not quieten a noisy bearing by preloading it: the 6000-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
- The open 6013 needs external sealing and application-supplied lubrication; in the SKF catalogue the protected variants are separate order numbers 6013-2Z (shields) and 6013-2RSH (contact seals), not suffix-free 6013.
- The 31.9/25 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6013 bearing?
A 6013 deep-groove ball bearing has a 65 mm bore, 100 mm outer diameter and 18 mm width (2.559 × 3.937 × 0.709 in), per ISO 15 boundary dimensions. It is an open bearing with no seals or shields.
What internal clearance does 6013 have?
Unless a clearance suffix says otherwise, 6013 is manufactured to normal (CN) radial internal clearance. Tight fits and hot shafts consume clearance in service — for those conditions order the C3 execution of 6013 and verify the residual clearance after mounting.
How should 6013 be mounted?
Apply the mounting force to the ring being fitted: on a 65 mm shaft seat the press load must pass through the inner-ring face only. Induction heating of the inner ring (max 120 °C) is the clean method at this size. Never strike the outer ring, the cage or the seals.
What lubrication does 6013 need?
The open 6013 is lubricated by the application; a NLGI 2 lithium-soap grease filled to roughly 25–35% of the free volume is the common choice, with a defined relubrication interval.
What is the SKF designation and catalogue data for 6013?
In the SKF Rolling Bearings catalogue this size is listed as 6013 — the open (unsealed) execution, 65×100×18 mm per ISO 15. Quoted values: C 31.9 kN, C0 25 kN, Pu 1.06 kN, limiting speed 9000 r/min, mass 440 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 6013.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.