6030-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6030-NSK model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6030 carries bore code 30 = 150 mm. Outside diameter 225 mm and width 35 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 150 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 150 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• Choosing the 60xx extra-light section saves radial space at 150 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6230 before committing to the smaller envelope.
• The open 6030-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 150×225×35 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 6030-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• A 150 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 35 mm-wide ring of 6030-NSK drags the lip and overheats it.
• The open 6030 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 150 mm bore places 6030 at the lower end of NSK's large-size range; at these diameters the pressed-steel cage is speed-limited and NSK commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NSK distributor, and do not extrapolate small-bore speed ratings to this size.
• At 138 kN dynamic load rating (C) and 126 kN static (C0), 6030 is a heavy-load NSK bearing for industrial gearboxes and large conveyors; NSK expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 4240 g (4.2 kg), 6030 needs mechanical handling for mounting; NSK recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 150×225×35 mm envelope of 6030 gives a D/d ratio of 1.50 and 37.5 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 138/126 kN load ratings, mass 4240 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6030 on the 150×225×35 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6030 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.