6030-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6030-ZZ-NTN model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6030 carries bore code 30 = 150 mm. Outside diameter 225 mm and width 35 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 150 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN catalogue order number: 6030ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 150 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 60xx extra-light section at 150 mm bore uses a smaller 225 mm OD than a 6230; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
• ZZ shields are non-contact: 6030-ZZ-NTN blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6030-2RS for that.
• Shielded 6030-ZZ-NTN units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Vibration during standstill brinells the raceways of a 150 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 225 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6030-ZZ-NTN.
• NTN catalogues the shielded version as 6030ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• The 150 mm bore places 6030 at the lower end of NTN's large-size range; at these diameters the pressed-steel cage is speed-limited and NTN commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NTN distributor, and do not extrapolate small-bore speed ratings to this size.
• NTN lists the grease limiting speed at 2800 r/min for 6030; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 139 kN dynamic load rating (C) and 126 kN static (C0), 6.55 kN fatigue load limit Cu, 6030 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 4080 g (4.1 kg), 6030 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 150×225×35 mm envelope of 6030 gives a D/d ratio of 1.50 and 37.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 139/126 kN load ratings, 6.55 kN fatigue load limit Cu NTN lists the grease limiting speed at 2800 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 4080 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6030ZZ on the 150×225×35 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6030 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.