6030-2RS-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6030-2RS-NTN model number is decoded

6030-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 30 by five gives the 150 mm bore; the 225 mm outside diameter and 35 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 150 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's contact-seal catalogue number is 6030LLU (suffix LLU, or LLH low-torque variant), mapped here from the industry-neutral -2RS spelling; the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 150 mm bore the ring mass is significant: heat 6030 on an induction heater (max 120 °C), never over an open flame, and plan puller access or a withdrawal sleeve now for the day it has to come off again.
• The 60xx extra-light section at 150 mm bore uses a smaller 225 mm OD than a 6230; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
• Heat is the enemy of the sealed 6030-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 6030-2RS-NTN in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Do not quieten a noisy bearing by preloading it: the 6000-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 225 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6030-2RS-NTN.
• NTN catalogues the contact-sealed version as 6030LLU (suffix LLU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.
• The 150 mm bore places 6030 at the lower end of NTN's large-size range; at these diameters the pressed-steel cage is speed-limited and NTN commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NTN distributor, and do not extrapolate small-bore speed ratings to this size.
• NTN lists the grease limiting speed at 1700 r/min for 6030; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 139 kN dynamic load rating (C) and 126 kN static (C0), 6.55 kN fatigue load limit Cu, 6030 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 4080 g (4.1 kg), 6030 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 150×225×35 mm envelope of 6030 gives a D/d ratio of 1.50 and 37.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 139/126 kN load ratings, 6.55 kN fatigue load limit Cu NTN lists the grease limiting speed at 1700 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 4080 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6030LLU on the 150×225×35 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6030 in a rated drive.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 6030 is listed.