608 bearing: complete specifications & equivalents
The 608 is a ISO 15 radial bearing sized 8 x 22 x 7 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 8 mm |
| Outer diameter D | 22 mm |
| Width B | 7 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 3.45 kN |
| Basic static load rating C0 | 1.37 kN |
| Fatigue load limit Pu | 0.057 kN |
| Reference speed (thermal) | 75000 rpm |
| Limiting speed (mechanical) | 48000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 12 g |
| Manufacturer designation | 608 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6000-series range
| Bore d | 0.315 in |
|---|---|
| Outer diameter D | 0.866 in |
| Width B | 0.276 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 7 mm |
| Smallest bore in 6000-series | 4 mm |
| Largest outer diameter in 6000-series | 1150 mm |
| Width range across 6000-series | 4–155 mm |
| Bore position in 6000-series (smallest first) | 5 of 61 |
| Bore above smallest 6000-series size | 4 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 608-2RS | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 8×22×7 mm envelope and equivalent catalogue ratings; 608-2RSH is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 608-RSR | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 8×22×7 mm envelope and equivalent catalogue ratings; 608-2RSL is the low-friction non-contact seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 608-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 8×22×7 mm envelope and equivalent catalogue ratings; 608-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| W608-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 8×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (3.45/1.37 kN vs 1.99/0.78 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| W608-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 8×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (3.45/1.37 kN vs 1.99/0.78 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| W608 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 8×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (3.45/1.37 kN vs 1.99/0.78 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 608 model number is decoded
In the 6000-series, the final digit is the bore in millimetres: 608 fits a 8 mm shaft (direct-number miniature spelling). The envelope is 8×22×7 mm (0.315×0.866×0.276 in) with a 7.0 mm radial section height, C 3.45 kN, C0 1.37 kN and Pu 0.057 kN. The open 608 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 48000 r/min, catalogue mass 12 g.
Typical equipment & failure modes
Common applications
- fractional-horsepower motors
- small fans and blowers
- hand-held power tools
- domestic appliances
Known failure patterns
- contamination wear when the open arrangement is used without external seals
- lubricant starvation where no regreasing interval is maintained
- fretting corrosion on a creeping shaft or housing seat
- cage damage from running beyond the limiting speed
Selection pitfalls — read before you substitute
- Fillet radii must clear the 608 chamfer so the 7 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- Fillet radii must clear the 608 chamfer so the 7 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- Open 608 needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
- Plan a relubrication interval for 608; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
- Clearance suffixes follow the seal code in the designation stack (e.g. 608-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
- At 8 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
- SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.
- SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
Frequently asked questions
What are the dimensions of 608?
The SKF 608 measures 8 mm bore × 22 mm OD × 7 mm width (0.315 × 0.866 × 0.276 in), mass about 12 g. It is open, with no shields or seals.
How do I read the 608 designation?
Small miniature bearings print the bore as the final digit, so 608 is a 8 mm bearing; the series digits in front give the section (OD/width family).
What internal clearance does 608 have?
Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.
How long can a greased 608 be stored?
Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.
What load can 608 take?
Catalogue values for 608: dynamic C 3.45 kN, static C0 1.37 kN, fatigue limit Pu 0.057 kN. Use C in life calculation and C0 for static checks at 8 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.