W608-ZZ bearing: complete specifications & equivalents
The W608-ZZ is a ISO 15 radial bearing sized 8 x 22 x 7 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 8 mm |
| Outer diameter D | 22 mm |
| Width B | 7 mm |
| Material | SS440C |
| Seal / shield | ZZ |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1.99 kN |
| Basic static load rating C0 | 0.78 kN |
| Fatigue load limit Pu | 0.034 kN |
| Reference speed (thermal) | 75000 rpm |
| Limiting speed (mechanical) | 38000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 12 g |
| Manufacturer designation | W 608-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6000-series range
| Bore d | 0.315 in |
|---|---|
| Outer diameter D | 0.866 in |
| Width B | 0.276 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 7 mm |
| Smallest bore in 6000-series | 4 mm |
| Largest outer diameter in 6000-series | 1150 mm |
| Width range across 6000-series | 4–155 mm |
| Bore position in 6000-series (smallest first) | 5 of 61 |
| Bore above smallest 6000-series size | 4 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 608 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 8×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (1.99/0.78 kN vs 3.45/1.37 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| 608-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 8×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (1.99/0.78 kN vs 3.45/1.37 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| 608-RSR | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 8×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (1.99/0.78 kN vs 3.45/1.37 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| 608-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 8×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (1.99/0.78 kN vs 3.45/1.37 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| W608-2RS | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 8×22×7 mm envelope and equivalent catalogue ratings; W 608-2RS1 is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| W608 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 8×22×7 mm envelope and equivalent catalogue ratings; W 608 is the open arrangement execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the W608-ZZ model number is decoded
The W prefix denotes SKF stainless steel deep-groove bearings (X108CrMo17 / AISI 440C class rings). In the 6000-series, the final digit is the bore in millimetres: 608 fits a 8 mm shaft (direct-number miniature spelling). Envelope 8×22×7 mm (0.315×0.866×0.276 in), C 1.99 kN, C0 0.78 kN, Pu 0.034 kN; limiting speed 38000 r/min and mass 12 g. SKF spells the double shield W 608-2Z (suffix 2Z); the shields are non-contact, retain grease and block coarse debris but are not liquid-tight. Stainless is chosen for corrosion and washdown duty, not for extra load — the same-envelope chrome-steel bearing rates higher.
Typical equipment & failure modes
Common applications
- washdown-duty equipment
- chemical and marine atmospheres
- medical and laboratory devices
- small pumps handling corrosive media
Known failure patterns
- seal and grease failure before the rings corrode in sustained washdown service
- surface staining and pitting when even the stainless steel is left unlubricated in salty or acidic duty
- fine-particle abrasion when non-contact shields let dust through in a dirty environment
- grease aging inside the shielded cavity with no relubrication path
Selection pitfalls — read before you substitute
- Temperatures above roughly 300 °C temper the stainless races; even standard greases fail far earlier — keep W608-ZZ inside the quoted grease temperature range.
- W-prefix stainless rings (X108CrMo17 / AISI 440C class) resist moisture and weak chemicals but will still rust in chloride-rich or salt-spray duty without protection — W608-ZZ is not marine-grade stainless.
- The stainless steel is martensitic and MAGNETIC; do not reject W608-ZZ over magnetism — only austenitic grades are non-magnetic, and those are too soft for bearing raceways.
- Stainless bearings carry lower load ratings than chrome steel of the same envelope: W608-ZZ is quoted at C 1.99 kN versus the 7 mm-wide 52100 version — do not swap on dimensions alone.
- At 8 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
- Catalogue ratings for W608-ZZ (C 1.99 kN, C0 0.78 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
Frequently asked questions
What are the dimensions of the stainless W608-ZZ?
SKF W 608-2Z measures 8×22×7 mm (0.315×0.866×0.276 in), about 12 g, C 1.99 kN.
What does the W in W 608-2Z mean?
W is the SKF prefix for stainless steel deep-groove bearings (rings in X108CrMo17 / AISI 440C class); the rest of the designation follows the normal series and bore rules.
Are W stainless bearings waterproof?
No — the stainless rings resist moisture and weak chemicals far better than 52100 chrome steel, but salt spray, strong chlorides and unlubricated washdown duty can still corrode W608-ZZ; add seals and food-grade grease for wet positions.
Can I replace a chrome-steel bearing with stainless W608-ZZ?
The envelope matches, but stainless rates lower (C 1.99 kN for W 608-2Z); for corrosive environments that trade-off is intended, for high loads it shortens life.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.