6080-M bearing: complete specifications & equivalents

The 6080-M is a ISO 15 radial bearing sized 400 x 600 x 90 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 600 mm d = 400 B = 90 mm side section front view
Principal dimensions: bore d 400 mm, outer diameter D 600 mm, width B 90 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 400 mm
Outer diameter D 600 mm
Width B 90 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 520 kN
Basic static load rating C0 865 kN
Fatigue load limit Pu 16.3 kN
Reference speed (thermal) 2000 rpm
Limiting speed (mechanical) 1700 rpm
Operating temperature -40 to +120 °C
Mass 87500 g
Manufacturer designation 6080 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6000-series range

Bore d15.748 in
Outer diameter D23.622 in
Width B3.543 in
ISO bore code80
Radial section height (D−d)/2100 mm
Smallest bore in 6000-series4 mm
Largest outer diameter in 6000-series1150 mm
Width range across 6000-series4–155 mm
Bore position in 6000-series (smallest first)48 of 61
Bore above smallest 6000-series size396 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6080 NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6080 on the same 400×600×90 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6080-M model number is decoded

In the 6000-series, the last two digits encode the bore: 6080 carries code 80 = 400 mm (code × 5). The envelope is 400×600×90 mm (15.748×23.622×3.543 in) with a 100.0 mm radial section height, C 520 kN, C0 865 kN and Pu 16.3 kN. The open 6080 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 1700 r/min, catalogue mass 87500 g.

Typical equipment & failure modes

Common applications

  • robotics and automation joints
  • lay shafts and idler shafts
  • textile and packaging machinery
  • slew and indexing drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • fretting corrosion on a creeping shaft or housing seat
  • cage damage from running beyond the limiting speed

Selection pitfalls — read before you substitute

  • At 400 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • The fatigue load limit is 16.3 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • The M suffix on 6080-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 87500 g quoted mass includes the heavier cage.
  • Open 6080-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6080-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Do not preload 6080-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.

Frequently asked questions

What are the dimensions of 6080-M?

The SKF 6080 M measures 400 mm bore × 600 mm OD × 90 mm width (15.748 × 23.622 × 3.543 in), mass about 87500 g. It is open, with no shields or seals.

How does the bore code in 6080 work?

The final two digits of 6080 are bore code 80, multiplied by 5 to give 400 mm.

What is the speed rating of 6080-M?

SKF lists a 2000 r/min thermal reference speed and a 1700 r/min mechanical limiting speed for 6080 M; real limits also depend on lubrication and fits.

What is the difference between 6080-M and a same-bore 62-series bearing?

Section height differs: 6080-M has a 100 mm radial section and C 520 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.

Which fits should I use for 6080-M?

With a rotating inner ring use roughly m6 on the shaft and H7 in the 600 mm housing; reverse the interference if the outer ring rotates.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.