6080 bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6080 model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6080 carries bore code 80 = 400 mm. Outside diameter 600 mm and width 90 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 400 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 400 mm of 6080 demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• Choosing the 60xx extra-light section saves radial space at 400 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6280 before committing to the smaller envelope.
• Storage matters for open bearings: 6080 leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 6000-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6080 units.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 600 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6080.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• The open 6080 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 400 mm bore places 6080 in NTN's upper maximum-size range; at this diameter the bearing mass is substantial and mounting requires induction heating of the inner ring (max 120 °C) with a mechanical puller. NTN supplies a machined brass cage (suffix M) and expects oil lubrication with a defined relubrication interval.
• NTN lists the grease limiting speed at only 930 r/min for 6080; this is a very large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 565 kN dynamic load rating (C) and 825 kN static (C0), 26.9 kN fatigue load limit Cu, 6080 is a very-heavy-load bearing for large industrial gearboxes and steel-mill equipment; NTN supplies a machined brass cage (suffix M) and expects an application review, because catalogue L10 life alone does not capture the shock and misalignment loads at this rating.
• At 87600 g (87.6 kg), 6080 is an extremely heavy bearing at the top of the single-row deep-groove range; NTN mandates induction heating (max 120 °C), a dedicated lifting fixture, and a machined brass cage (suffix M). Consult NTN engineering for the mounting and handling procedure before installation.
• The 400×600×90 mm envelope of 6080 gives a D/d ratio of 1.50 and 100.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 565/825 kN load ratings, 26.9 kN fatigue load limit Cu NTN lists the grease limiting speed at 930 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 87600 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6080 on the 400×600×90 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6080 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 6080 is listed.