618-800-MA bearing: complete specifications & equivalents

The 618-800-MA is a ISO 15 radial bearing sized 800 x 980 x 82 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 980 mm d = 800 B = 82 mm side section front view
Principal dimensions: bore d 800 mm, outer diameter D 980 mm, width B 82 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 800 mm
Outer diameter D 980 mm
Width B 82 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 559 kN
Basic static load rating C0 1370 kN
Fatigue load limit Pu 19.3 kN
Reference speed (thermal) 1000 rpm
Limiting speed (mechanical) 850 rpm
Operating temperature -40 to +120 °C
Mass 130000 g
Manufacturer designation 618/800 MA
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 61800-series range

Bore d31.496 in
Outer diameter D38.583 in
Width B3.228 in
ISO bore code—
Radial section height (D−d)/290 mm
Smallest bore in 61800-series1 mm
Largest outer diameter in 61800-series1820 mm
Width range across 61800-series1–140 mm
Bore position in 61800-series (smallest first)65 of 74
Bore above smallest 61800-series size799 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 618-800-MA model number is decoded

In the large-bore 61800-series, the bore is written directly after the slash as 800 mm (large thin-section bores use the slash spelling instead of the two-digit code). The envelope is 800×980×82 mm (31.496×38.583×3.228 in) with a 90.0 mm radial section height, C 559 kN, C0 1370 kN and Pu 19.3 kN. The open 618/800 MA carries no shields or seals and relies on application lubrication and external sealing. The MA suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 850 r/min, catalogue mass 130000 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.

Typical equipment & failure modes

Common applications

  • heavy conveyor drives
  • hoists and winches
  • industrial fans and blowers
  • mill and kiln auxiliaries

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded
  • brinelling from static overload or hammer blows during mounting

Selection pitfalls — read before you substitute

  • Fillet radii must clear the 618-800-MA chamfer so the 82 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • Do not preload 618-800-MA to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • The MA suffix on 618-800-MA denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 130000 g quoted mass includes the heavier cage.
  • Open 618-800-MA needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 618-800-MA; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 618/800-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.
  • For positions that need relubrication, choose the open execution of 618/800 and design the housing with a grease path; shielded and sealed versions are intended as fit-and-forget units.

Frequently asked questions

What are the dimensions of 618-800-MA?

The SKF 618/800 MA measures 800 mm bore × 980 mm OD × 82 mm width (31.496 × 38.583 × 3.228 in), mass about 130000 g. It is open, with no shields or seals.

Why is there a slash in the designation 618/800 MA?

The slash writes a bore that falls outside the two-digit code table: 618/800 means 800 mm bore. The site slug 618-800-MA replaces the slash with a hyphen.

How heavy is 618-800-MA?

Catalogue mass is 130000 g for 618/800 MA; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 618-800-MA have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 618-800-MA be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.