61817-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61817-RSR-NTN model number is decoded

61817-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 17 by five gives the 85 mm bore; the 110 mm outside diameter and 13 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 85 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6817LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• Only 12.5 mm of radial section separates bore and OD on the 618xx series at 85 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6217.
• RSR low-friction seals on 61817-RSR-NTN run faster than contact-seal 61817-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61817-2RS instead.
• The low-drag lip of 61817-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 61817-RSR-NTN-C3. No clearance suffix means normal CN clearance.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61800-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• NTN catalogues this low-friction non-contact seal as 6817LLB (suffix LB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 85 mm bore 61817 is in NTN's medium industrial range; the pressed-steel cage is standard but large-section 63xx/64xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 5700 r/min the grease limiting speed for 61817 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• At 20.7 kN dynamic load rating (C) and 19 kN static (C0), 1.26 kN fatigue load limit Cu, 61817 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 270 g, 61817 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 85×110×13 mm envelope of 61817 gives a D/d ratio of 1.29 and only 12.5 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 20.7/19 kN load ratings, 1.26 kN fatigue load limit Cu NTN lists the grease limiting speed at 5700 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 270 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6817LLB on the 85×110×13 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61817 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.