61819-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61819-NTN model number is decoded

61819 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 19 by five gives the 95 mm bore; the 120 mm outside diameter and 13 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 95 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 95 mm of 61819-NTN demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• The 618xx thin section at 95 mm bore has only a 12.5 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6219.
• The open 61819-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 95×120×13 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61819 units.
• Do not quieten a noisy bearing by preloading it: the 61800-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61800-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• The open 61819 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• At 95 mm bore 61819 is in NTN's medium industrial range; the pressed-steel cage is standard but large-section 63xx/64xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 5000 r/min the grease limiting speed for 61819 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• At 21.4 kN dynamic load rating (C) and 20.5 kN static (C0), 1.31 kN fatigue load limit Cu, 61819 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 300 g, 61819 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 95×120×13 mm envelope of 61819 gives a D/d ratio of 1.26 and only 12.5 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 21.4/20.5 kN load ratings, 1.31 kN fatigue load limit Cu NTN lists the grease limiting speed at 5000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 300 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6819 on the 95×120×13 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61819 in a rated drive.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61819 is listed.