619-800-MA bearing: complete specifications & equivalents

The 619-800-MA is a ISO 15 radial bearing sized 800 x 1060 x 115 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 1060 mm d = 800 B = 115 mm side section front view
Principal dimensions: bore d 800 mm, outer diameter D 1060 mm, width B 115 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 800 mm
Outer diameter D 1060 mm
Width B 115 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 832 kN
Basic static load rating C0 2040 kN
Fatigue load limit Pu 28.5 kN
Reference speed (thermal) 950 rpm
Limiting speed (mechanical) 800 rpm
Operating temperature -40 to +120 °C
Mass 275000 g
Manufacturer designation 619/800 MA
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 61900-series range

Bore d31.496 in
Outer diameter D41.732 in
Width B4.528 in
ISO bore code—
Radial section height (D−d)/2130 mm
Smallest bore in 61900-series3 mm
Largest outer diameter in 61900-series1120 mm
Width range across 61900-series3–118 mm
Bore position in 61900-series (smallest first)62 of 63
Bore above smallest 61900-series size797 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 619-800-MA model number is decoded

In the large-bore 61900-series, the bore is written directly after the slash as 800 mm (large thin-section bores use the slash spelling instead of the two-digit code). The envelope is 800×1060×115 mm (31.496×41.732×4.528 in) with a 130.0 mm radial section height, C 832 kN, C0 2040 kN and Pu 28.5 kN. The open 619/800 MA carries no shields or seals and relies on application lubrication and external sealing. The MA suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 800 r/min, catalogue mass 275000 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.

Typical equipment & failure modes

Common applications

  • mill and kiln auxiliaries
  • pulp and paper machinery
  • marine deck machinery
  • crusher auxiliary drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Catalogue ratings for 619-800-MA (C 832 kN, C0 2040 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Deep-groove geometry tolerates only minutes of misalignment; if the 1060 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 619-800-MA.
  • The MA suffix on 619-800-MA denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 275000 g quoted mass includes the heavier cage.
  • Open 619-800-MA needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 619-800-MA; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Catalogue ratings for 619-800-MA (C 832 kN, C0 2040 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 619-800-MA?

The SKF 619/800 MA measures 800 mm bore × 1060 mm OD × 115 mm width (31.496 × 41.732 × 4.528 in), mass about 275000 g. It is open, with no shields or seals.

Why is there a slash in the designation 619/800 MA?

The slash writes a bore that falls outside the two-digit code table: 619/800 means 800 mm bore. The site slug 619-800-MA replaces the slash with a hyphen.

How long can a greased 619-800-MA be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 619-800-MA take?

Catalogue values for 619/800 MA: dynamic C 832 kN, static C0 2040 kN, fatigue limit Pu 28.5 kN. Use C in life calculation and C0 for static checks at 800 mm bore.

What is the speed rating of 619-800-MA?

SKF lists a 950 r/min thermal reference speed and a 800 r/min mechanical limiting speed for 619/800 MA; real limits also depend on lubrication and fits.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.