61910-2RS-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61910-2RS-NTN model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61910 carries bore code 10 = 50 mm. Outside diameter 72 mm and width 12 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 50 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's contact-seal catalogue number is 6910LLU (suffix LLU, or LLH low-torque variant), mapped here from the industry-neutral -2RS spelling; the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61910 with C3 for those conditions.
• The 619xx thin section at 50 mm bore (11.0 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• Heat is the enemy of the sealed 61910-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 61910-2RS-NTN in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 61910-2RS-NTN-C3. No clearance suffix means normal CN clearance.
• A 50 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• NTN catalogues the contact-sealed version as 6910LLU (suffix LU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.
• The 50 mm bore puts 61910 in NTN's general-purpose industrial range; the standard pressed-steel cage and CN clearance cover most electric-motor and pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• At 5100 r/min the grease limiting speed for 61910 covers medium-duty industrial drives; the contact seal (LLU) is the main speed limiter here — for continuous operation above 80% of this figure use the open variant with an external labyrinth seal and oil bath.
• NTN rates 61910 at 14.9 kN dynamic (C) and 11.2 kN static (C0), 0.77 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 132 g, 61910 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 50×72×12 mm envelope of 61910 gives a D/d ratio of 1.44 and 11.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 14.9/11.2 kN load ratings, 0.77 kN fatigue load limit Cu NTN lists the grease limiting speed at 5100 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 132 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6910LLU on the 50×72×12 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61910 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• Standard catalogue stock of 61910 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.