61910-2RS bearing: complete specifications & equivalents
The 61910-2RS is a ISO 15 radial bearing sized 50 x 72 x 12 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 50 mm |
| Outer diameter D | 72 mm |
| Width B | 12 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 14.6 kN |
| Basic static load rating C0 | 11.8 kN |
| Fatigue load limit Pu | 0.5 kN |
| Limiting speed (mechanical) | 5600 rpm |
| Operating temperature | -30 to +110 °C |
| Mass | 140 g |
| Manufacturer designation | SKF 61910-2RS1 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 1.969 in |
|---|---|
| Outer diameter D | 2.835 in |
| Width B | 0.472 in |
| ISO bore code | 10 |
| Radial section height (D−d)/2 | 11 mm |
| Smallest bore in 61900-series | 3 mm |
| Largest outer diameter in 61900-series | 1120 mm |
| Width range across 61900-series | 3–118 mm |
| Bore position in 61900-series (smallest first) | 18 of 63 |
| Bore above smallest 61900-series size | 47 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61910-2RS-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 61910-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×72×12 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 61910-RSR-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×72×12 mm envelope per ISO 15; seal variant differs (2RS vs RSR) — confirm sealing suits the duty. |
| 61910-ZZ | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×72×12 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
| 61910-2RS-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 61910-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×72×12 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 61910-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×72×12 mm envelope per ISO 15; seal variant differs (2RS vs RSR) — confirm sealing suits the duty. |
| 61910-ZZ-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×72×12 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61910-2RS model number is decoded
In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61910 carries bore code 10 = 50 mm. Outside diameter 72 mm and width 12 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 50 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. SKF's contact-seal catalogue number is 61910-2RS1 (older text: -2RS1), mapped here from the industry-neutral -2RS spelling.
Typical equipment & failure modes
Common applications
- robotics and automation joints
- lay shafts and idler shafts
- textile machinery
- packaging machinery
Known failure patterns
- seal-lip hardening and loss of pre-grease in sustained high-temperature service
- grease-life expiry in the sealed-for-life cavity (no relubrication path)
- rolling-contact fatigue spalling after the rated L10 life is exceeded
- brinelling from static overload or hammering during mounting
Selection pitfalls — read before you substitute
- Interference on a 50 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 61910 with C3 clearance and re-check the residual value after mounting.
- The 619xx thin section at 50 mm bore (11.0 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
- Contact seals add drag and heat: 61910-2RS runs slower and cooler-limited than the open 61910; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
- Never wash a sealed 61910-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
- Measure the shaft, do not trust the drawing: a 50 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61910-2RS.
- Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61900-series position can soften the mixture and leak — clean out the old fill before switching grease types.
- SKF catalogues the contact-sealed version as 61910-2RS1 (older printings may read -2RS1); it is shipped pre-greased and its 5600 r/min limiting speed is set by seal-lip drag and grease life versus the open bearing's 19000 r/min thermal reference speed.
- The 14.6/11.8 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61910-2RS bearing?
A 61910-2RS deep-groove ball bearing has a 50 mm bore, 72 mm outer diameter and 12 mm width (1.969 × 2.835 × 0.472 in), per ISO 15 boundary dimensions. It is fitted with two contact rubber seals and is normally pre-greased.
What does the 2RS suffix on 61910-2RS mean?
2RS means two contact elastomer seals, one each side, usually over a lifetime grease fill. Sealing against dust and moisture is better than ZZ shields, but the lip drag lowers the speed and temperature ceiling.
How does the 61900 compare with other series at the same 50 mm bore?
619 is a thin section one step above 618: 72×12 mm with an 11.0 mm radial section at 50 mm bore; a 6210 on the same bore is substantially larger and more heavily rated.
Are 61910 bearings from different brands interchangeable?
For boundary dimensions, yes: every brand's 61910 uses the same ISO 15 envelope (50×72×12 mm). Load ratings, limiting speeds, clearance, precision class and sealing design can differ, so verify those in the supplier catalogue when substituting. Seal suffixes also differ by brand (2RS, DDU, LLU, 2RSL and similar).
What is the SKF designation and catalogue data for 61910-2RS?
In the SKF Rolling Bearings catalogue this size is listed as 61910-2RS1 — two contact elastomer seals over a lifetime grease fill, 50×72×12 mm per ISO 15. Quoted values: C 14.6 kN, C0 11.8 kN, Pu 0.5 kN, limiting speed 5600 r/min, mass 140 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61910-2RS.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.